EFM32 Pearl Gecko 12 (SLSTK3402A)
Overview
The EFM32 Pearl Gecko 12 Starter Kit SLSTK3402A contains an MCU from the EFM32PG family built on an ARM® Cortex®-M4F processor with excellent low power capabilities.
EFM32PG12 SLSTK3402A (image courtesy of Silicon Labs)
Hardware
Advanced Energy Monitoring provides real-time information about the energy consumption of an application or prototype design.
Ultra low power 128x128 pixel Memory-LCD
2 user buttons, 2 LEDs and a touch slider
Humidity, temperature, and inductive-capacitive metal sensor
On-board Segger J-Link USB debugger
For more information about the EFM32PG SoC and SLSTK3402A board:
Supported Features
The slstk3402a board configuration supports the following hardware features:
Interface |
Controller |
Driver/Component |
|---|---|---|
MPU |
on-chip |
memory protection unit |
NVIC |
on-chip |
nested vector interrupt controller |
SYSTICK |
on-chip |
systick |
COUNTER |
on-chip |
rtcc |
FLASH |
on-chip |
flash memory |
GPIO |
on-chip |
gpio |
UART |
on-chip |
serial port-polling; serial port-interrupt |
I2C |
on-chip |
i2c port-polling |
WATCHDOG |
on-chip |
watchdog |
TRNG |
on-chip |
true random number generator |
The default configuration can be found in boards/silabs/starter_kits/slstk3402a/slstk3402a_efm32pg12b500f1024gl125_defconfig
The default configuration when building using this board to develop for the EFM32JG12 SoC can be found in boards/silabs/starter_kits/slstk3402a/slstk3402a_efm32jg12b500f1024gl125_defconfig
Other hardware features are currently not supported by the port.
EFM32 Jade Gecko SoC
The EFM32 Pearl Gecko Starter Kit SLSTK3402A can also be used to evaluate the EFM32 Jade Gecko SoC (EFM32JG12). The only difference between the Pearl Gecko and the Jade Gecko is their core. The Pearl Gecko contains an ARM® Cortex®-M4F core, and the Jade Gecko an ARM® Cortex®-M3 core. Other features such as memory and peripherals are the same.
Code that is built for the Jade Gecko also runs on an equivalent Pearl Gecko.
To build firmware for the Jade Gecko and run it on the EFM32 Pearl Gecko Starter
Kit, use the board slstk3402a/efm32jg12b500f1024gl125 instead of
slstk3402a/efm32pg12b500f1024gl125.
Connections and IOs
The EFM32PG12 SoC has twelve GPIO controllers (PORTA to PORTL), but only four are currently enabled (PORTA, PORTB, PORTD and PORTF) for the SLSTK3402A board.
In the following table, the column Name contains pin names. For example, PE2 means pin number 2 on PORTE, as used in the board’s datasheets and manuals.
Name |
Function |
Usage |
|---|---|---|
PF4 |
GPIO |
LED0 |
PF5 |
GPIO |
LED1 |
PF6 |
GPIO |
Push Button PB0 |
PF7 |
GPIO |
Push Button PB1 |
PA5 |
GPIO |
Board Controller Enable EFM_BC_EN |
PA0 |
UART_TX |
UART TX Console VCOM_TX US0_TX #0 |
PA1 |
UART_RX |
UART RX Console VCOM_RX US0_RX #0 |
PD10 |
UART_TX |
EXP12_UART_TX LEU0_TX #18 |
PD11 |
UART_RX |
EXP14_UART_RX LEU0_RX #18 |
PC10 |
I2C_SDA |
ENV_I2C_SDA I2C0_SDA #15 |
PC11 |
I2C_SCL |
ENV_I2C_SCL I2C0_SCL #15 |
System Clock
The EFM32PG12 SoC is configured to use the 40 MHz external oscillator on the board.
Serial Port
The EFM32PG12 SoC has four USARTs and one Low Energy UART (LEUART).
Programming and Debugging
Note
Before using the kit the first time, you should update the J-Link firmware from J-Link-Downloads
Flashing
The SLSTK3402A includes an J-Link serial and debug adaptor built into the board. The adaptor provides:
A USB connection to the host computer, which exposes a mass storage device and a USB serial port.
A serial flash device, which implements the USB flash disk file storage.
A physical UART connection which is relayed over interface USB serial port.
Flashing an application to SLSTK3402A
The sample application Hello World is used for this example. Build the Zephyr kernel and application:
# From the root of the zephyr repository
west build -b slstk3402a/efm32pg12b500f1024gl125 samples/hello_world
Connect the SLSTK3402A to your host computer using the USB port and you should see a USB connection which exposes a mass storage device(STK3402A). Copy the generated zephyr.bin to the STK3402A drive.
Use a USB-to-UART converter such as an FT232/CP2102 to connect to the UART on the expansion header.
Open a serial terminal (minicom, putty, etc.) with the following settings:
Speed: 115200
Data: 8 bits
Parity: None
Stop bits: 1
Reset the board and you’ll see the following message on the corresponding serial port terminal session:
Hello World! slstk3402a