The latest development version of this page may be more current than this released 3.7.0 version.

ti,lp5036 (on i2c bus)

Description

Texas Instruments LP5036 I2C LED controller node

Properties

Top level properties

These property descriptions apply to “ti,lp5036” nodes themselves. This page also describes child node properties in the following sections.

Properties not inherited from the base binding file.

Name	Type	Details
`supply-gpios`	`phandle-array`	GPIO specifier that controls power to the device. This property should be provided when the device has a dedicated switch that controls power to the device. The supply state is entirely the responsibility of the device driver. Contrast with vin-supply.
`vin-supply`	`phandle`	Reference to the regulator that controls power to the device. The referenced devicetree node must have a regulator compatible. This property should be provided when device power is supplied by a shared regulator. The supply state is dependent on the request status of all devices fed by the regulator. Contrast with supply-gpios. If both properties are provided then the regulator must be requested before the supply GPIOS is set to an active state, and the supply GPIOS must be set to an inactive state before releasing the regulator.
`enable-gpios`	`phandle-array`	GPIO to use to enable/disable the controller.
`max_curr_opt`	`boolean`	If enabled the maximum current output is set to 35 mA (25.5 mA else).
`log_scale_en`	`boolean`	If enabled a logarithmic dimming scale curve is used for LED brightness control. A linear dimming scale curve is used else.

Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “ti,lp5036” compatible.

Name	Type	Details
`wakeup-source`	`boolean`	Property to identify that a device can be used as wake up source. When this property is provided a specific flag is set into the device that tells the system that the device is capable of wake up the system. Wake up capable devices are disabled (interruptions will not wake up the system) by default but they can be enabled at runtime if necessary.
`power-domain`	`phandle`	Power domain the device belongs to. The device will be notified when the power domain it belongs to is either suspended or resumed.
`zephyr,pm-device-runtime-auto`	`boolean`	Automatically configure the device for runtime power management after the init function runs.
`zephyr,disabling-power-states`	`phandles`	List of power states that will disable this device power.
`status`	`string`	indicates the operational status of a device Legal values: `'ok'`, `'okay'`, `'disabled'`, `'reserved'`, `'fail'`, `'fail-sss'` See Important properties for more information.
`compatible`	`string-array`	compatible strings This property is required. See Important properties for more information.
`reg`	`array`	device address on i2c bus This property is required. See Important properties for more information.
`reg-names`	`string-array`	name of each register space
`interrupts`	`array`	interrupts for device See Important properties for more information.
`interrupts-extended`	`compound`	extended interrupt specifier for device
`interrupt-names`	`string-array`	name of each interrupt
`interrupt-parent`	`phandle`	phandle to interrupt controller node
`label`	`string`	Human readable string describing the device (used as device_get_binding() argument) See Important properties for more information. This property is deprecated.
`clocks`	`phandle-array`	Clock gate information
`clock-names`	`string-array`	name of each clock
`#address-cells`	`int`	number of address cells in reg property
`#size-cells`	`int`	number of size cells in reg property
`dmas`	`phandle-array`	DMA channels specifiers
`dma-names`	`string-array`	Provided names of DMA channel specifiers
`io-channels`	`phandle-array`	IO channels specifiers
`io-channel-names`	`string-array`	Provided names of IO channel specifiers
`mboxes`	`phandle-array`	mailbox / IPM channels specifiers
`mbox-names`	`string-array`	Provided names of mailbox / IPM channel specifiers
`zephyr,deferred-init`	`boolean`	Do not initialize device automatically on boot. Device should be manually initialized using device_init().

Child node properties

Name

Type

Details

label

string

Human readable string describing the LED

This property is required.

See Important properties for more information.

index

int

Index of the LED on a controller. It can be used by drivers or
applications to map a logical LED to its real position on the
controller. For example, this allows to handle boards where the
LEDs in an array/strip are not wired following the LED order of
the controller.

This property is required.

color-mapping

array

Channel to color mapping of a multicolor LED. If a LED supports
several colors, then the color-mapping property can be used to
describe how the hardware channels and the colors are mapped.

For example the channel to color mapping of RGB LEDs would be

   color-mapping =
        <LED_COLOR_ID_RED>,
        <LED_COLOR_ID_GREEN>,
        <LED_COLOR_ID_BLUE>;

This property is required.