renesas,smartbond-pinctrl
Vendor: Renesas Electronics Corporation
Description
The SmartBond pin controller is a singleton node responsible for controlling
pin function selection and pin properties, such as routing a UART RX to pin
P1.8 and enabling the pullup resistor on that pin.
The node has the 'pinctrl' node label set in your SoC's devicetree,
so you can modify it like this:
&pinctrl {
/* your modifications go here */
};
All device pin configurations should be placed in child nodes of the
'pinctrl' node, as shown in this example:
/* You can put this in places like a board-pinctrl.dtsi file in
* your board directory, or a devicetree overlay in your application.
*/
/* include definitions and utility macros for the SoC used by the board */
#include <dt-bindings/pinctrl/smartbond-pinctrl.h>
&pinctrl {
/* configuration for uart device, default state */
uart_default: uart_default {
/* group 1 */
group1 {
/* route UART TX to P0.9 */
pinmux = <SMARTBOND_PINMUX(UART_TX, 0, 9)>;
};
/* group 2 */
group2 {
/* route UART RX to P0.8 and enable pull-up */
pinmux = <SMARTBOND_PINMUX(UART_RX, 0, 8)>;
bias-pull-up;
};
};
};
The 'uart0_default' child node encodes the pin configurations for a
particular state of a device; in this case, the default (that is, active)
state.
As shown, pin configurations are organized in groups within each child node.
Each group can specify a list of pin function selections in the 'pinmux'
property. Note that 'pinmux' property is an array so you can configure multiple
pins at once there. The SMARTBOND_PINMUX macro is used to create pinmux value.
A group can also specify shared pin properties common to all the specified
pins, such as the 'bias-pull-up' property in group 2. Here is a list of
supported standard pin properties:
- bias-pull-up: Enable pull-up resistor.
- bias-pull-down: Enable pull-down resistor.
Note that bias options are mutually exclusive.
To link this pin configuration with a device, use a pinctrl-N property
for some number N, like this example you could place in your board's DTS
file:
#include "board-pinctrl.dtsi"
&uart {
pinctrl-0 = <&uart_default>;
pinctrl-names = "default";
};
Properties
Top level properties
These property descriptions apply to “renesas,smartbond-pinctrl” nodes themselves. This page also describes child node properties in the following sections.
Properties not inherited from the base binding file.
(None)
Deprecated properties not inherited from the base binding file.
(None)
Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “renesas,smartbond-pinctrl” compatible.
Name |
Type |
Details |
|---|---|---|
|
|
Property to identify that a device can be used as wake up source.
When this property is provided a specific flag is set into the
device that tells the system that the device is capable of
wake up the system.
Wake up capable devices are disabled (interruptions will not wake up
the system) by default but they can be enabled at runtime if necessary.
|
|
|
Power domain the device belongs to.
The device will be notified when the power domain it belongs to is either
suspended or resumed.
|
|
|
Automatically configure the device for runtime power management after the
init function runs.
|
|
|
List of power states that will disable this device power.
|
|
|
indicates the operational status of a device
Legal values: See Important properties for more information. |
|
|
compatible strings
This property is required. See Important properties for more information. |
|
|
register space
See Important properties for more information. |
|
|
name of each register space
|
|
|
interrupts for device
See Important properties for more information. |
|
|
extended interrupt specifier for device
|
|
|
name of each interrupt
|
|
|
phandle to interrupt controller node
|
|
|
Human readable string describing the device (used as device_get_binding() argument)
See Important properties for more information. This property is deprecated. |
|
|
Clock gate information
|
|
|
name of each clock
|
|
|
number of address cells in reg property
|
|
|
number of size cells in reg property
|
|
|
DMA channels specifiers
|
|
|
Provided names of DMA channel specifiers
|
|
|
IO channels specifiers
|
|
|
Provided names of IO channel specifiers
|
|
|
mailbox / IPM channels specifiers
|
|
|
Provided names of mailbox / IPM channel specifiers
|
|
|
Do not initialize device automatically on boot. Device should be manually
initialized using device_init().
|
Grandchild node properties
Name |
Type |
Details |
|---|---|---|
|
|
enable pull-up resistor
|
|
|
enable pull-down resistor
|
|
|
enable input on pin (e.g. enable an input buffer, no effect on output)
|
|
|
enable output on a pin without actively driving it (e.g. enable an output
buffer)
|
|
|
An array of pins sharing the same group properties. The pins should
be defined using the SMARTBOND_PINMUX utility macro that encodes the port,
pin and function.
This property is required. |