ams,tmd2620 (on i2c bus)
Vendor: AMS AG
Description
OSRAM ams TMD2620 Proximity Sensor
Properties
Properties not inherited from the base binding file.
Name |
Type |
Details |
|---|---|---|
|
|
Human readable string describing the sensor. It can be used to
distinguish multiple instances of the same model (e.g., lid accelerometer
vs. base accelerometer in a laptop) to a host operating system.
This property is defined in the Generic Sensor Property Usages of the HID
Usage Tables specification
(https://usb.org/sites/default/files/hut1_3_0.pdf, section 22.5).
|
|
|
GPIO specifier that controls power to the device.
This property should be provided when the device has a dedicated
switch that controls power to the device. The supply state is
entirely the responsibility of the device driver.
Contrast with vin-supply.
|
|
|
Reference to the regulator that controls power to the device.
The referenced devicetree node must have a regulator compatible.
This property should be provided when device power is supplied
by a shared regulator. The supply state is dependent on the
request status of all devices fed by the regulator.
Contrast with supply-gpios. If both properties are provided
then the regulator must be requested before the supply GPIOS is
set to an active state, and the supply GPIOS must be set to an
inactive state before releasing the regulator.
|
|
|
The interrupt pin of TMD2620 is open-drain, active low.
If connected directly the MCU, the pin should be configured
as pull-up, active low.
This property is required. |
|
|
Proximity detection gain of the sensor
This property is required. Legal values: |
|
|
IR led pulse length in ms
This property is required. Legal values: |
|
|
count of IR led pulses (min. 1; max. 64)
This property is required. |
|
|
high threshold for interrupt. (min. 0; max. 255)
|
|
|
low threshold for interrupt. (min. 0; max. 255)
|
|
|
LED drive strength in multiples of 6mA (min. 0; max. 31)
This property is required. |
|
|
filters proximity interrupt. (min. 0; max. 15)
0-> every cycle fires an interrupt
1-> 1 consecutive proximity value out of threshold range fires an interrupt
2-> 2 consecutive proximity values out of threshold range fires an interrupt
...
|
|
|
Enables wait mode
|
|
|
time the sensor waits between proximity cycles. (min. 0; max 255).
given in multiples of 2.81 starting at 0 for 2.81ms wait time.
|
|
|
increases the wait time by a factor of x12
|
Deprecated properties not inherited from the base binding file.
(None)
Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “ams,tmd2620” compatible.
Name |
Type |
Details |
|---|---|---|
|
|
Property to identify that a device can be used as wake up source.
When this property is provided a specific flag is set into the
device that tells the system that the device is capable of
wake up the system.
Wake up capable devices are disabled (interruptions will not wake up
the system) by default but they can be enabled at runtime if necessary.
|
|
|
Power domain the device belongs to.
The device will be notified when the power domain it belongs to is either
suspended or resumed.
|
|
|
Automatically configure the device for runtime power management after the
init function runs.
|
|
|
List of power states that will disable this device power.
|
|
|
indicates the operational status of a device
Legal values: See Important properties for more information. |
|
|
compatible strings
This property is required. See Important properties for more information. |
|
|
register space
This property is required. See Important properties for more information. |
|
|
name of each register space
|
|
|
interrupts for device
See Important properties for more information. |
|
|
extended interrupt specifier for device
|
|
|
name of each interrupt
|
|
|
phandle to interrupt controller node
|
|
|
Human readable string describing the device (used as device_get_binding() argument)
See Important properties for more information. This property is deprecated. |
|
|
Clock gate information
|
|
|
name of each clock
|
|
|
number of address cells in reg property
|
|
|
number of size cells in reg property
|
|
|
DMA channels specifiers
|
|
|
Provided names of DMA channel specifiers
|
|
|
IO channels specifiers
|
|
|
Provided names of IO channel specifiers
|
|
|
mailbox / IPM channels specifiers
|
|
|
Provided names of mailbox / IPM channel specifiers
|
|
|
Do not initialize device automatically on boot. Device should be manually
initialized using device_init().
|