nxp,kinetis-lpuart
Vendor: NXP Semiconductors
Description
These nodes are “uart” bus nodes.
Kinetis LPUART
Properties
Properties not inherited from the base binding file.
Name |
Type |
Details |
|---|---|---|
|
|
Clock frequency information for UART operation
|
|
|
Initial baud rate setting for UART
|
|
|
Set to enable RTS/CTS flow control at boot time
|
|
|
Configures the parity of the adapter. Enumeration id 0 for none, 1 for odd
and 2 for even parity. Default to none if not specified.
Legal values: |
|
|
Sets the number of stop bits.
Legal values: |
|
|
Sets the number of data bits.
Legal values: |
|
|
Invert the binary logic of tx pin. When enabled, physical logic levels are inverted and
we use 1=Low, 0=High instead of 1=High, 0=Low.
|
|
|
Invert the binary logic of rx pin. When enabled, physical logic levels are inverted and
we use 1=Low, 0=High instead of 1=High, 0=Low.
|
|
|
Pin configuration/s for the first state. Content is specific to the
selected pin controller driver implementation.
|
|
|
Pin configuration/s for the second state. See pinctrl-0.
|
|
|
Pin configuration/s for the third state. See pinctrl-0.
|
|
|
Pin configuration/s for the fourth state. See pinctrl-0.
|
|
|
Pin configuration/s for the fifth state. See pinctrl-0.
|
|
|
Names for the provided states. The number of names needs to match the
number of states.
|
|
|
Enable loopback mode on LPUART peripheral. When present, RX pin is
disconnected, and transmitter output is internally connected to
the receiver input.
|
|
|
Enable the single wire half-duplex communication.
Using this mode, TX and RX lines are internally connected and
only TX pin is used afterwards and should be configured.
RX/TX conflicts must be handled on user side.
|
|
|
Set to enable RTS signal, which can be used to enable the driver
of an external RS-485 transceiver. Note hw-flow-control should be
set to false.
|
|
|
RTS polarity at RS485 mode.
|
Deprecated properties not inherited from the base binding file.
(None)
Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “nxp,kinetis-lpuart” compatible.
Name |
Type |
Details |
|---|---|---|
|
|
Property to identify that a device can be used as wake up source.
When this property is provided a specific flag is set into the
device that tells the system that the device is capable of
wake up the system.
Wake up capable devices are disabled (interruptions will not wake up
the system) by default but they can be enabled at runtime if necessary.
|
|
|
Power domain the device belongs to.
The device will be notified when the power domain it belongs to is either
suspended or resumed.
|
|
|
Automatically configure the device for runtime power management after the
init function runs.
|
|
|
List of power states that will disable this device power.
|
|
|
indicates the operational status of a device
Legal values: See Important properties for more information. |
|
|
compatible strings
This property is required. See Important properties for more information. |
|
|
register space
This property is required. See Important properties for more information. |
|
|
name of each register space
|
|
|
interrupts for device
See Important properties for more information. |
|
|
extended interrupt specifier for device
|
|
|
name of each interrupt
|
|
|
phandle to interrupt controller node
|
|
|
Human readable string describing the device (used as device_get_binding() argument)
See Important properties for more information. This property is deprecated. |
|
|
Clock gate information
|
|
|
name of each clock
|
|
|
number of address cells in reg property
|
|
|
number of size cells in reg property
|
|
|
DMA channels specifiers
|
|
|
Provided names of DMA channel specifiers
|
|
|
IO channels specifiers
|
|
|
Provided names of IO channel specifiers
|
|
|
mailbox / IPM channels specifiers
|
|
|
Provided names of mailbox / IPM channel specifiers
|
|
|
Do not initialize device automatically on boot. Device should be manually
initialized using device_init().
|