nuvoton,numaker-usbd
Vendor: Nuvoton Technology Corporation
Description
These nodes are “usb” bus nodes.
Nuvoton NuMaker USB 1.1 device controller
Properties
Properties not inherited from the base binding file.
Name |
Type |
Details |
|---|---|---|
|
|
Configures USB controllers to work up to a specific speed. Valid arguments are "super-speed", "high-speed", "full-speed" and "low-speed". If this is not passed via DT, USB controllers should use their maximum hardware capability.
Legal values: |
|
|
Control VBUS via GPIO pin.
|
|
|
Number of bi-directional endpoints supported by hardware
(including EP0)
This property is required. |
|
|
Number of IN endpoints supported by hardware
(including EP0 IN)
|
|
|
Number of OUT endpoints supported by hardware
(including EP0 OUT)
|
|
|
Reset information
This property is required. |
|
|
Name of each reset
|
|
|
Pin configuration/s for the first state. Content is specific to the
selected pin controller driver implementation.
|
|
|
Pin configuration/s for the second state. See pinctrl-0.
|
|
|
Pin configuration/s for the third state. See pinctrl-0.
|
|
|
Pin configuration/s for the fourth state. See pinctrl-0.
|
|
|
Pin configuration/s for the fifth state. See pinctrl-0.
|
|
|
Names for the provided states. The number of names needs to match the
number of states.
|
|
|
Size of DMA buffer in bytes
This property is required. |
|
|
Some soc series don't allow Isochronous IN/OUT endpoints to be assigned the same numbers,
for example, 0x82 (for Isochronous IN) and 0x02 (for Isochronous OUT) are disallowed.
|
Deprecated properties not inherited from the base binding file.
(None)
Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “nuvoton,numaker-usbd” compatible.
Name |
Type |
Details |
|---|---|---|
|
|
Property to identify that a device can be used as wake up source.
When this property is provided a specific flag is set into the
device that tells the system that the device is capable of
wake up the system.
Wake up capable devices are disabled (interruptions will not wake up
the system) by default but they can be enabled at runtime if necessary.
|
|
|
Power domain the device belongs to.
The device will be notified when the power domain it belongs to is either
suspended or resumed.
|
|
|
Automatically configure the device for runtime power management after the
init function runs.
|
|
|
List of power states that will disable this device power.
|
|
|
indicates the operational status of a device
Legal values: See Important properties for more information. |
|
|
compatible strings
This property is required. See Important properties for more information. |
|
|
register space
This property is required. See Important properties for more information. |
|
|
name of each register space
|
|
|
interrupts for device
This property is required. See Important properties for more information. |
|
|
extended interrupt specifier for device
|
|
|
name of each interrupt
|
|
|
phandle to interrupt controller node
|
|
|
Human readable string describing the device (used as device_get_binding() argument)
See Important properties for more information. This property is deprecated. |
|
|
Clock gate information
This property is required. |
|
|
name of each clock
|
|
|
number of address cells in reg property
|
|
|
number of size cells in reg property
|
|
|
DMA channels specifiers
|
|
|
Provided names of DMA channel specifiers
|
|
|
IO channels specifiers
|
|
|
Provided names of IO channel specifiers
|
|
|
mailbox / IPM channels specifiers
|
|
|
Provided names of mailbox / IPM channel specifiers
|
|
|
Do not initialize device automatically on boot. Device should be manually
initialized using device_init().
|