The latest development version of this page may be more current than this released 4.0.0 version.

EFR32xG27 Dev Kit (xG27-DK2602A)

Silicon Labs xG27-DK2602A is a Dev Kit using the EFR32BG27 SoC. The kit consists of the EFR32BG27 +8 dBm Dev Kit Board (BRD2602A).

Hardware

  • EFR32BG27 Blue Gecko Wireless SoC with up to 76.8 MHz operating frequency

  • ARM® Cortex® M33 core with 64 kB RAM and 768 kB Flash

  • Macronix ultra low power 8-Mbit SPI flash (MX25R8035F)

  • 2.4 GHz ceramic antenna for wireless transmission

  • Silicon Labs Si7021 relative humidity and temperature sensor

  • Vishay VEML6035 low power, high sensitivity ambient light Sensor

  • Silicon Labs Si7210 hall effect sensor

  • TDK InvenSense ICM-20689 6-axis inertial sensor

  • Pair of PDM microphones

  • One LED and one push button

  • Power enable signals and isolation switches for ultra low power operation

  • On-board SEGGER J-Link debugger for easy programming and debugging, which includes a USB virtual COM port and Packet Trace Interface (PTI)

  • Mini Simplicity connector for access to energy profiling and advanced wireless network debugging

  • Breakout pads for GPIO access and connection to external hardware

  • Reset button

  • CR2032 coin cell holder and external battery connector

For more information, refer to these documents:

Supported Features

The xg27_dk2602a board configuration supports the following hardware features:

Interface

Controller

Driver/Component

NVIC

on-chip

nested vector interrupt controller

SYSTICK

on-chip

systick

FLASH

on-chip

flash memory

GPIO

on-chip

gpio

UART

on-chip

serial

Flashing

The xG27 Dev Kit includes an embedded J-Link adapter built around EFM32GG12 microcontroller (not user-programmable). The adapter provides:

  • SWD interface to EFR32BG27 for flashing and debugging.

  • SWO trace interface to EFR32BG27 for tracing.

  • UART interface to EFR32BG27 for console access.

  • A USB connection to the host computer, which exposes CDC-ACM Serial Port endpoints for access to the console UART interface and proprietary J-Link endpoints for access to the SWD and SWO interfaces.

UART functionality of the adapter is accessible via standard CDC-ACM USB driver present in most desktop operating systems and any standard serial port terminal program e.g. picocom.

SWD and SWO functionality is accessible via Simplicity Commander.

The simplest way to flash the board is by using West, which runs Simplicity Commander in unattended mode and passes all the necessary arguments to it.

  • If Simplicity Commander is installed in the system and the directory in which commander executable is located is present in the PATH environment variable:

    west flash

  • Otherwise, one should specify full path to the commander executable:

    west flash --commander <path_to_commander_directory>/commander

  • In case several J-Link adapters are connected, you must specify serial number of the adapter which should be used for flashing:

    west flash --dev-id <J-Link serial number>

Programming and Debugging

The sample application Hello World is used for this example. Build the Zephyr kernel and application:

# From the root of the zephyr repository
west build -b xg27_dk2602a samples/hello_world

Connect your device to your host computer using the USB port and you should see a USB connection. Use west’s flash command

Open a serial terminal (minicom, putty, etc.) with the following settings:

  • Speed: 115200

  • Data: 8 bits

  • Parity: None

  • Stop bits: 1

Reset the board and you should be able to see on the corresponding Serial Port the following message:

Hello World! xg27_dk2602a