The latest development version of this page may be more current than this released 4.0.0 version.

ti,lmp90080 (on spi bus)

Note

An implementation of a driver matching this compatible is available in drivers/adc/adc_lmp90xxx.c.

Description

These nodes are “lmp90xxx” bus nodes.

Texas Instruments LMP90080 AFE binding

Properties

Top level properties

These property descriptions apply to “ti,lmp90080” nodes themselves. This page also describes child node properties in the following sections.

Properties not inherited from the base binding file.

Name	Type	Details
`rtd-current`	`int`	RTD current in microampere
`drdyb-gpios`	`phandle-array`	Data Ready Bar
`#io-channel-cells`	`int`	This property is required. Constant value: `1`
`spi-max-frequency`	`int`	Maximum clock frequency of device's SPI interface in Hz This property is required.
`duplex`	`int`	Duplex mode, full or half. By default it's always full duplex thus 0 as this is, by far, the most common mode. Use the macros not the actual enum value, here is the concordance list (see dt-bindings/spi/spi.h) 0 SPI_FULL_DUPLEX 2048 SPI_HALF_DUPLEX Legal values: `0`, `2048`
`frame-format`	`int`	Motorola or TI frame format. By default it's always Motorola's, thus 0 as this is, by far, the most common format. Use the macros not the actual enum value, here is the concordance list (see dt-bindings/spi/spi.h) 0 SPI_FRAME_FORMAT_MOTOROLA 32768 SPI_FRAME_FORMAT_TI Legal values: `0`, `32768`
`spi-cpol`	`boolean`	SPI clock polarity which indicates the clock idle state. If it is used, the clock idle state is logic high; otherwise, low.
`spi-cpha`	`boolean`	SPI clock phase that indicates on which edge data is sampled. If it is used, data is sampled on the second edge; otherwise, on the first edge.
`spi-hold-cs`	`boolean`	In some cases, it is necessary for the master to manage SPI chip select under software control, so that multiple spi transactions can be performed without releasing it. A typical use case is variable length SPI packets where the first spi transaction reads the length and the second spi transaction reads length bytes.
`supply-gpios`	`phandle-array`	GPIO specifier that controls power to the device. This property should be provided when the device has a dedicated switch that controls power to the device. The supply state is entirely the responsibility of the device driver. Contrast with vin-supply.
`vin-supply`	`phandle`	Reference to the regulator that controls power to the device. The referenced devicetree node must have a regulator compatible. This property should be provided when device power is supplied by a shared regulator. The supply state is dependent on the request status of all devices fed by the regulator. Contrast with supply-gpios. If both properties are provided then the regulator must be requested before the supply GPIOS is set to an active state, and the supply GPIOS must be set to an inactive state before releasing the regulator.

Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “ti,lmp90080” compatible.

Name	Type	Details
`#address-cells`	`int`	number of address cells in reg property Constant value: `1`
`#size-cells`	`int`	number of size cells in reg property
`status`	`string`	indicates the operational status of a device Legal values: `'ok'`, `'okay'`, `'disabled'`, `'reserved'`, `'fail'`, `'fail-sss'` See Important properties for more information.
`compatible`	`string-array`	compatible strings This property is required. See Important properties for more information.
`reg`	`array`	register space This property is required. See Important properties for more information.
`reg-names`	`string-array`	name of each register space
`interrupts`	`array`	interrupts for device See Important properties for more information.
`interrupts-extended`	`compound`	extended interrupt specifier for device
`interrupt-names`	`string-array`	name of each interrupt
`interrupt-parent`	`phandle`	phandle to interrupt controller node
`label`	`string`	Human readable string describing the device (used as device_get_binding() argument) See Important properties for more information. This property is deprecated.
`clocks`	`phandle-array`	Clock gate information
`clock-names`	`string-array`	name of each clock
`dmas`	`phandle-array`	DMA channels specifiers
`dma-names`	`string-array`	Provided names of DMA channel specifiers
`io-channels`	`phandle-array`	IO channels specifiers
`io-channel-names`	`string-array`	Provided names of IO channel specifiers
`mboxes`	`phandle-array`	mailbox / IPM channels specifiers
`mbox-names`	`string-array`	Provided names of mailbox / IPM channel specifiers
`power-domains`	`phandle-array`	Power domain specifiers
`power-domain-names`	`string-array`	Provided names of power domain specifiers
`#power-domain-cells`	`int`	Number of cells in power-domains property
`zephyr,deferred-init`	`boolean`	Do not initialize device automatically on boot. Device should be manually initialized using device_init().
`wakeup-source`	`boolean`	Property to identify that a device can be used as wake up source. When this property is provided a specific flag is set into the device that tells the system that the device is capable of wake up the system. Wake up capable devices are disabled (interruptions will not wake up the system) by default but they can be enabled at runtime if necessary.
`zephyr,pm-device-runtime-auto`	`boolean`	Automatically configure the device for runtime power management after the init function runs.
`zephyr,disabling-power-states`	`phandles`	List of power states that will disable this device power.

Child node properties

Name	Type	Details
`reg`	`array`	Channel identifier. This property is required. See Important properties for more information.
`zephyr,gain`	`string`	Gain selection: - ADC_GAIN_1_6: x 1/6 - ADC_GAIN_1_5: x 1/5 - ADC_GAIN_1_4: x 1/4 - ADC_GAIN_1_3: x 1/3 - ADC_GAIN_2_5: x 2/5 - ADC_GAIN_1_2: x 1/2 - ADC_GAIN_2_3: x 2/3 - ADC_GAIN_4_5: x 4/5 - ADC_GAIN_1: x 1 - ADC_GAIN_2: x 2 - ADC_GAIN_3: x 3 - ADC_GAIN_4: x 4 - ADC_GAIN_6: x 6 - ADC_GAIN_8: x 8 - ADC_GAIN_12: x 12 - ADC_GAIN_16: x 16 - ADC_GAIN_24: x 24 - ADC_GAIN_32: x 32 - ADC_GAIN_64: x 64 - ADC_GAIN_128: x 128 This property is required. Legal values: `'ADC_GAIN_1_6'`, `'ADC_GAIN_1_5'`, `'ADC_GAIN_1_4'`, `'ADC_GAIN_1_3'`, `'ADC_GAIN_2_5'`, `'ADC_GAIN_1_2'`, `'ADC_GAIN_2_3'`, `'ADC_GAIN_4_5'`, `'ADC_GAIN_1'`, `'ADC_GAIN_2'`, `'ADC_GAIN_3'`, `'ADC_GAIN_4'`, `'ADC_GAIN_6'`, `'ADC_GAIN_8'`, `'ADC_GAIN_12'`, `'ADC_GAIN_16'`, `'ADC_GAIN_24'`, `'ADC_GAIN_32'`, `'ADC_GAIN_64'`, `'ADC_GAIN_128'`
`zephyr,reference`	`string`	Reference selection: - ADC_REF_VDD_1: VDD - ADC_REF_VDD_1_2: VDD/2 - ADC_REF_VDD_1_3: VDD/3 - ADC_REF_VDD_1_4: VDD/4 - ADC_REF_INTERNAL: Internal - ADC_REF_EXTERNAL0: External, input 0 - ADC_REF_EXTERNAL1: External, input 1 This property is required. Legal values: `'ADC_REF_VDD_1'`, `'ADC_REF_VDD_1_2'`, `'ADC_REF_VDD_1_3'`, `'ADC_REF_VDD_1_4'`, `'ADC_REF_INTERNAL'`, `'ADC_REF_EXTERNAL0'`, `'ADC_REF_EXTERNAL1'`
`zephyr,vref-mv`	`int`	This property can be used to specify the voltage (in millivolts) of the reference selected for this channel, so that applications can get that value if needed for some calculations. For the internal reference, the voltage can be usually obtained with a dedicated ADC API call, so there is no need to use this property in that case, but for other references this property can be useful.
`zephyr,acquisition-time`	`int`	Acquisition time. Use the ADC_ACQ_TIME macro to compose the value for this property or pass ADC_ACQ_TIME_DEFAULT to use the default setting for a given hardware (e.g. when the hardware does not allow to configure the acquisition time). This property is required.
`zephyr,differential`	`boolean`	When set, selects differential input mode for the channel. Otherwise, single-ended mode is used unless the zephyr,input-negative property is specified, in which case the differential mode is selected implicitly.
`zephyr,input-positive`	`int`	Positive ADC input. Used only for drivers that select the ADC_CONFIGURABLE_INPUTS Kconfig option.
`zephyr,input-negative`	`int`	Negative ADC input. Used only for drivers that select the ADC_CONFIGURABLE_INPUTS Kconfig option. When specified, implies the differential input mode for the channel.
`zephyr,resolution`	`int`	ADC resolution to be used for the channel.
`zephyr,oversampling`	`int`	Oversampling setting to be used for the channel. When specified, each sample is averaged from 2^N conversion results (where N is the provided value).
`zephyr,current-source-pin`	`uint8-array`	Output pin selection for the current sources. The actual interpretation depends on the driver. This is used only for drivers which select the ADC_CONFIGURABLE_EXCITATION_CURRENT_SOURCE_PIN Kconfig option.
`zephyr,vbias-pins`	`int`	Output pin selection for the bias voltage. The actual interpretation depends on the driver. This is used only for drivers which select the ADC_CONFIGURABLE_VBIAS_PIN Kconfig option.

Specifier cell names

io-channel cells: input