The latest development version of this page may be more current than this released 4.0.0 version.

atmel,sam-i2c-twim

Vendor: Atmel Corporation

Note

An implementation of a driver matching this compatible is available in drivers/i2c/i2c_sam4l_twim.c.

Description

These nodes are “i2c” bus nodes.

Atmel SAM4L Family I2C (TWIM) node

The Atmel Two-wire Master Interface (TWIM) interconnects components on a
unique two-wire bus, made up of one clock line and one data line with speeds
of up to 3.4 Mbit/s, based on a byte-oriented transfer format.  The TWIM is
always a bus master and can transfer sequential or single bytes.  Multiple
master capability is supported.  Arbitration of the bus is performed
internally and relinquishes the bus automatically if the bus arbitration is
lost.

When using speeds above standard mode, user may need adjust clock and data
lines slew and strength parameters.  In general, slew 0 and minimal strength
is enough for short buses and light loads.  As a reference, the below
is the lowest power configuration:

  std-clk-slew-lim = <0>;
  std-clk-strength-low = "0.5";
  std-data-slew-lim = <0>;
  std-data-strength-low = "0.5";

  hs-clk-slew-lim = <0>;
  hs-clk-strength-high = "0.5";
  hs-clk-strength-low = "0.5";
  hs-data-slew-lim = <0>;
  hs-data-strength-low = "0.5";

For best performances, user can tune the slope curves using an osciloscope.
The tuning should be performed by groups defined <mode>-<line>.  The prefix
std-<line> configures fast/fast-plus mode speeds and hs-<line> selects the
high speed mode.  The tune should be performed for both clock and data lines
on both speed modes.

Properties

Node specific propertiesDeprecated node specific propertiesBase properties

Properties not inherited from the base binding file.

Name	Type	Details
std-clk-slew-lim	int	Slew limit of the TWCK output buffer. This should be adjusted with std-clk-strength-low to fine tune the TWCK slope. This property is required. Legal values: 0, 1, 2, 3
std-clk-strength-low	string	Pull-down drive strength of the TWCK output buffer in fast/fast plus mode. This should be adjusted to provide proper TWCK line fall time. The value represents the port output current in mA when signal on low level. This property is required. Legal values: '0.5', '1.0', '1.6', '3.1', '6.2', '9.3', '15.5', '21.8'
std-data-slew-lim	int	Slew limit of the TWD output buffer. This should be adjusted with std-data-strength-low to fine tune the TWD slope. This property is required. Legal values: 0, 1, 2, 3
std-data-strength-low	string	Pull-down drive strength of the TWD output buffer in fast/fast plus mode. This should be adjusted to provide proper TWD line fall time. The value represents the port output current in mA when signal on low level. This property is required. Legal values: '0.5', '1.0', '1.6', '3.1', '6.2', '9.3', '15.5', '21.8'
hs-clk-slew-lim	int	Slew limit of the TWCK output buffer in high speed mode. This should be adjusted with both hs-clk-strength-high and hs-clk-strength-low to fine tune the TWCK slope. This property is required. Legal values: 0, 1, 2, 3
hs-clk-strength-high	string	Pull-up drive strength of the TWCK output buffer in high speed mode. This should be adjusted to provide proper TWCK line rise time. The value represents the port output current in mA when signal on high level. This property is required. Legal values: '0.5', '1.0', '1.5', '3.0'
hs-clk-strength-low	string	Pull-down drive strength of the TWCK output buffer in high speed mode. This should be adjusted to provide proper TWCK line fall time. The value represents the port output current in mA when signal on low level. This property is required. Legal values: '0.5', '1.0', '1.6', '3.1', '6.2', '9.3', '15.5', '21.8'
hs-data-slew-lim	int	Slew limit of the TWD output buffer in high speed mode. This should be adjusted with hs-data-strength-low to fine tune the TWD slope. This property is required. Legal values: 0, 1, 2, 3
hs-data-strength-low	string	Pull-down drive strength of the TWD output buffer in high speed mode. This should be adjusted to provide proper TWD line fall time. The value represents the port output current in mA when signal on low level. Legal values: '0.5', '1.0', '1.6', '3.1', '6.2', '9.3', '15.5', '21.8'
hs-master-code	int	3-bit code to be prefixed with 0b00001 to form a unique 8-bit HS-mode master code (0000 1XXX) This property is required. Legal values: 0, 1, 2, 3, 4, 5, 6, 7
clock-frequency	int	Initial clock frequency in Hz
sq-size	int	Size of the submission queue for blocking requests Default value: 4
cq-size	int	Size of the completion queue for blocking requests Default value: 4
pinctrl-0	phandles	Pin configuration/s for the first state. Content is specific to the selected pin controller driver implementation.
pinctrl-1	phandles	Pin configuration/s for the second state. See pinctrl-0.
pinctrl-2	phandles	Pin configuration/s for the third state. See pinctrl-0.
pinctrl-3	phandles	Pin configuration/s for the fourth state. See pinctrl-0.
pinctrl-4	phandles	Pin configuration/s for the fifth state. See pinctrl-0.
pinctrl-names	string-array	Names for the provided states. The number of names needs to match the number of states.