The latest development version of this page may be more current than this released 4.0.0 version.

generic-fem-two-ctrl-pins

Description

This is a representation of generic radio Front-End Module (FEM)
that has a two-pin control interface (CTX, CRX).

The CTX control pin is used to enable the Power Amplifier (PA) in
the transmit path. This is therefore sometimes referred to as
the "PA pin" in other contexts.

The CRX control pin is used to enable the Low Noise Amplifier
(LNA) in the receive path, and is sometimes referred to as
the "LNA pin" in other contexts.

Each of these pins is optional, and may be omitted if not present.
(Though if you do specify a pin, you must also specify its
corresponding settle-time-us property.)

Properties

Properties not inherited from the base binding file.

Name	Type	Details
`ctx-gpios`	`phandle-array`	SoC GPIO connected to the CTX input pin on the FEM device.
`crx-gpios`	`phandle-array`	SoC GPIO connected to the CRX input pin on the FEM device.
`ctx-settle-time-us`	`int`	Desired minimum settling time, in microseconds, from assertion of the CTX pin to beginning of transmission.
`crx-settle-time-us`	`int`	Desired minimum settling time, in microseconds, from assertion of the CRX pin to beginning of reception.
`tx-gain-db`	`int`	TX gain of the PA of the FEM device, in dB.
`rx-gain-db`	`int`	RX gain of the LNA of the FEM device, in dB.

Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “generic-fem-two-ctrl-pins” compatible.

Name	Type	Details
`status`	`string`	indicates the operational status of a device Legal values: `'ok'`, `'okay'`, `'disabled'`, `'reserved'`, `'fail'`, `'fail-sss'` See Important properties for more information.
`compatible`	`string-array`	compatible strings This property is required. See Important properties for more information.
`reg`	`array`	register space See Important properties for more information.
`reg-names`	`string-array`	name of each register space
`interrupts`	`array`	interrupts for device See Important properties for more information.
`interrupts-extended`	`compound`	extended interrupt specifier for device
`interrupt-names`	`string-array`	name of each interrupt
`interrupt-parent`	`phandle`	phandle to interrupt controller node
`label`	`string`	Human readable string describing the device (used as device_get_binding() argument) See Important properties for more information. This property is deprecated.
`clocks`	`phandle-array`	Clock gate information
`clock-names`	`string-array`	name of each clock
`#address-cells`	`int`	number of address cells in reg property
`#size-cells`	`int`	number of size cells in reg property
`dmas`	`phandle-array`	DMA channels specifiers
`dma-names`	`string-array`	Provided names of DMA channel specifiers
`io-channels`	`phandle-array`	IO channels specifiers
`io-channel-names`	`string-array`	Provided names of IO channel specifiers
`mboxes`	`phandle-array`	mailbox / IPM channels specifiers
`mbox-names`	`string-array`	Provided names of mailbox / IPM channel specifiers
`power-domains`	`phandle-array`	Power domain specifiers
`power-domain-names`	`string-array`	Provided names of power domain specifiers
`#power-domain-cells`	`int`	Number of cells in power-domains property
`zephyr,deferred-init`	`boolean`	Do not initialize device automatically on boot. Device should be manually initialized using device_init().
`wakeup-source`	`boolean`	Property to identify that a device can be used as wake up source. When this property is provided a specific flag is set into the device that tells the system that the device is capable of wake up the system. Wake up capable devices are disabled (interruptions will not wake up the system) by default but they can be enabled at runtime if necessary.
`zephyr,pm-device-runtime-auto`	`boolean`	Automatically configure the device for runtime power management after the init function runs.
`zephyr,disabling-power-states`	`phandles`	List of power states that will disable this device power.