The latest development version of this page may be more current than this released 4.0.0 version.

st,iis2iclx (on i2c bus)

Vendor: STMicroelectronics

Note

An implementation of a driver matching this compatible is available in drivers/sensor/st/iis2iclx/iis2iclx.c.

Description

STMicroelectronics IIS2ICLX 2-axis accelerometer sensor
accessed through I2C bus

Properties

Properties not inherited from the base binding file.

Name

Type

Details

supply-gpios

phandle-array

 
GPIO specifier that controls power to the device.

This property should be provided when the device has a dedicated
switch that controls power to the device.  The supply state is
entirely the responsibility of the device driver.

Contrast with vin-supply.

vin-supply

phandle

 
Reference to the regulator that controls power to the device.
The referenced devicetree node must have a regulator compatible.

This property should be provided when device power is supplied
by a shared regulator.  The supply state is dependent on the
request status of all devices fed by the regulator.

Contrast with supply-gpios.  If both properties are provided
then the regulator must be requested before the supply GPIOS is
set to an active state, and the supply GPIOS must be set to an
inactive state before releasing the regulator.

drdy-gpios

phandle-array

 
DRDY pin

This pin defaults to active high when produced by the sensor.
The property value should ensure the flags properly describe
the signal that is presented to the driver.

int-pin

int

 
Select DRDY pin number (1 or 2).

This number represents which of the two interrupt pins
(INT1 or INT2) the drdy line is attached to. This property is not
mandatory and if not present it defaults to 1 which is the
configuration at power-up.

- 1 # drdy is generated from INT1
- 2 # drdy is generated from INT2

Default value: 1

Legal values: 1, 2

range

int

 
Range in g. Default is power-up configuration.

- 0 # IIS2ICLX_DT_FS_500mG (0.015 mg/LSB)
- 1 # IIS2ICLX_DT_FS_3G    (0.122 mg/LSB)
- 2 # IIS2ICLX_DT_FS_1G    (0.031 mg/LSB)
- 3 # IIS2ICLX_DT_FS_2G    (0.061 mg/LSB)

Default value: 3

Legal values: 0, 1, 2, 3

odr

int

 
Specify the default accelerometer output data rate expressed in samples per second (Hz).
Default is power-up configuration.

- 0  # IIS2ICLX_DT_ODR_OFF
- 1  # IIS2ICLX_DT_ODR_12Hz5
- 2  # IIS2ICLX_DT_ODR_26H
- 3  # IIS2ICLX_DT_ODR_52Hz
- 4  # IIS2ICLX_DT_ODR_104Hz
- 5  # IIS2ICLX_DT_ODR_208Hz
- 6  # IIS2ICLX_DT_ODR_416Hz
- 7  # IIS2ICLX_DT_ODR_833Hz

Legal values: 0, 1, 2, 3, 4, 5, 6, 7

friendly-name

string

 
Human readable string describing the sensor. It can be used to
distinguish multiple instances of the same model (e.g., lid accelerometer
vs. base accelerometer in a laptop) to a host operating system.

This property is defined in the Generic Sensor Property Usages of the HID
Usage Tables specification
(https://usb.org/sites/default/files/hut1_3_0.pdf, section 22.5).