WCH CH32V003EVT
Overview
The WCH [1] CH32V003EVT hardware provides support for QingKe 32-bit RISC-V2A processor and the following devices:
CLOCK
GPIO
NVIC
The board is equipped with two LEDs. The WCH webpage on CH32V003 [2] contains the processor’s information and the datasheet.
Hardware
The QingKe 32-bit RISC-V2A processor of the WCH CH32V003EVT is clocked by an external crystal and runs at 48 MHz.
Supported Features
The ch32v003evt board supports the hardware features listed below.
- on-chip / on-board
- Feature integrated in the SoC / present on the board.
- 2 / 2
-
Number of instances that are enabled / disabled.
Click on the label to see the first instance of this feature in the board/SoC DTS files. -
vnd,foo -
Compatible string for the Devicetree binding matching the feature.
Click on the link to view the binding documentation.
Type |
Location |
Description |
Compatible |
|---|---|---|---|
CPU |
on-chip |
WCH QingKe V2 RISC-V MCU1 |
|
Clock control |
on-chip |
WCH CH32V00x Reset and Clock Control (RCC)1 |
|
on-chip |
WCH CH32V00x HSE Clock1 |
||
on-chip |
WCH CH32V00x HSI Clock1 |
||
on-chip |
Generic fixed-rate clock provider1 |
||
on-chip |
WCH CH32V00x PLL1 |
||
DMA |
on-chip |
WCH DMA controller1 |
|
GPIO & Headers |
on-chip |
WCH CH32V00x General-Purpose Input/Output (GPIO)3 |
|
Interrupt controller |
on-chip |
WCH CH32V00x Programmable Fast Interrupt Controller (PFIC)1 |
|
LED |
on-board |
Group of GPIO-controlled LEDs1 |
|
MTD |
on-chip |
Flash node1 |
|
Pin control |
on-chip |
WCH CH32V00x AFIO1 |
|
Serial controller |
on-chip |
WCH CH32V00x UART1 |
|
SRAM |
on-chip |
Generic on-chip SRAM description1 |
|
Timer |
on-chip |
WCH CH32V00x Systick1 |
Connections and IOs
LED
LED1 = Unconnected. Connect to an I/O pin (PD4).
Programming and Debugging
Applications for the ch32v003evt board target can be built and flashed
in the usual way (see Building an Application and Run an Application
for more details); however, an external programmer is required since the board
does not have any built-in debug support.
The following pins of the external programmer must be connected to the following pins on the PCB (see image):
VCC = VCC (do not power the board from the USB port at the same time)
GND = GND
SWIO = PD1
Flashing
You can use minichlink to flash the board. Once minichlink has been set
up, build and flash applications as usual (see Building an Application and
Run an Application for more details).
Here is an example for the Blinky application.
# From the root of the zephyr repository
west build -b ch32v003evt samples/basic/blinky
west flash
Debugging
This board can be debugged via OpenOCD or minichlink.
Testing the LED on the WCH CH32V003EVT
There is 1 sample program that allow you to test that the LED on the board is working properly with Zephyr:
samples/basic/blinky
You can build and flash the examples to make sure Zephyr is running correctly on your board. The button and LED definitions can be found in boards/wch/ch32v003evt/ch32v003evt.dts.