Zephyr API Documentation 4.0.0-rc3
A Scalable Open Source RTOS
Loading...
Searching...
No Matches
xlnx_gem.h
Go to the documentation of this file.
1/*
2 * Copyright (c) 2021-2022, Weidmueller Interface GmbH & Co. KG
3 * SPDX-License-Identifier: Apache-2.0
4 */
5
6#ifndef ZEPHYR_INCLUDE_DT_BINDINGS_ETHERNET_XLNX_GEM_H_
7#define ZEPHYR_INCLUDE_DT_BINDINGS_ETHERNET_XLNX_GEM_H_
8
9/* PHY auto-detection alias */
10#define XLNX_GEM_PHY_AUTO_DETECT 0
11
12/*
13 * MDC divider values
14 *
15 * According to the ZynqMP's gem.network_config register documentation (UG1087),
16 * divider /32 is the reset value. The network_config[mdc_clock_division]
17 * documentation in UG1087 is likely wrong (copied directly from the Zynq-7000),
18 * as it claims that the MDC clock division is applied to the cpu_1x clock
19 * which the UltraScale doesn't have. Contradicting information is provided in
20 * the UltraScale TRM (UG1085), which mentions in chapter 34, section "Configure
21 * the PHY", p. 1074, that the MDC clock division is applied to the IOU_SWITCH_CLK.
22 * Xilinx's emacps driver doesn't (or no longer does) limit the range of dividers
23 * on the UltraScale compared to the Zynq-7000.
24 * -> Contrary to earlier revisions of this driver, all dividers are available
25 * to both the UltraScale and the Zynq-7000.
26 */
27
28#define XLNX_GEM_MDC_DIVIDER_8 0 /* cpu_1x or IOU_SWITCH_CLK < 20 MHz */
29#define XLNX_GEM_MDC_DIVIDER_16 1 /* cpu_1x or IOU_SWITCH_CLK 20 - 40 MHz */
30#define XLNX_GEM_MDC_DIVIDER_32 2 /* cpu_1x or IOU_SWITCH_CLK 40 - 80 MHz */
31#define XLNX_GEM_MDC_DIVIDER_48 3 /* cpu_1x or IOU_SWITCH_CLK 80 - 120 MHz */
32#define XLNX_GEM_MDC_DIVIDER_64 4 /* cpu_1x or IOU_SWITCH_CLK 120 - 160 MHz */
33#define XLNX_GEM_MDC_DIVIDER_96 5 /* cpu_1x or IOU_SWITCH_CLK 160 - 240 MHz */
34#define XLNX_GEM_MDC_DIVIDER_128 6 /* cpu_1x or IOU_SWITCH_CLK 240 - 320 MHz */
35#define XLNX_GEM_MDC_DIVIDER_224 7 /* cpu_1x or IOU_SWITCH_CLK 320 - 540 MHz */
36
37/* Link speed values */
38#define XLNX_GEM_LINK_SPEED_10MBIT 1
39#define XLNX_GEM_LINK_SPEED_100MBIT 2
40#define XLNX_GEM_LINK_SPEED_1GBIT 3
41
42/* AMBA AHB data bus width */
43#define XLNX_GEM_AMBA_AHB_DBUS_WIDTH_32BIT 0
44#define XLNX_GEM_AMBA_AHB_DBUS_WIDTH_64BIT 1
45#define XLNX_GEM_AMBA_AHB_DBUS_WIDTH_128BIT 2
46
47/* AMBA AHB burst length */
48#define XLNX_GEM_AMBA_AHB_BURST_SINGLE 1
49#define XLNX_GEM_AMBA_AHB_BURST_INCR4 4
50#define XLNX_GEM_AMBA_AHB_BURST_INCR8 8
51#define XLNX_GEM_AMBA_AHB_BURST_INCR16 16
52
53/* Hardware RX buffer size */
54#define XLNX_GEM_HW_RX_BUFFER_SIZE_1KB 0
55#define XLNX_GEM_HW_RX_BUFFER_SIZE_2KB 1
56#define XLNX_GEM_HW_RX_BUFFER_SIZE_4KB 2
57#define XLNX_GEM_HW_RX_BUFFER_SIZE_8KB 3
58
59#endif /* ZEPHYR_INCLUDE_DT_BINDINGS_ETHERNET_XLNX_GEM_H_ */