INFINEON CYW920829M2EVK-02
Overview
The AIROC™ CYW20829 Bluetooth® LE MCU Evaluation Kit (CYW920829M2EVK-02) with its included on-board peripherals enables evaluation, prototyping, and development of a wide array of Bluetooth® Low Energy applications, all on Infineon’s low power, high performance AIROC™ CYW20829. The AIROC™ CYW20829’s robust RF performance and 10 dBm TX output power without an external power amplifier (PA). This provides enough link budget for the entire spectrum of Bluetooth® LE use cases including industrial IoT applications, smart home, asset tracking, beacons and sensors, and medical devices.
The system features Dual Arm® Cortex® - M33s for powering the MCU and Bluetooth subsystem with programmable and reconfigurable analog and digital blocks. In addition, on the kit, there is a suite of on-board peripherals including six-axis inertial measurement unit (IMU), thermistor, analog mic, user programmable buttons (2), LEDs (2), and RGB LED. There is also extensive GPIO support with extended headers and Arduino Uno R3 compatibility for third-party shields.
Hardware
For more information about the CYW20829 SoC and CYW920829M2EVK-02 board:
Kit Features:
AIROC™ CYW20829 Bluetooth® LE MCU in 56 pin QFN package
Arduino compatible headers for hardware expansion
On-board sensors - 6-axis IMU, Thermistor, Infineon analog microphone, and Infineon digital microphone
User switches, RGB LED and user LEDs
USB connector for power, programming and USB-UART bridge
Kit Contents:
CYW20829 evaluation board (CYW9BTM2BASE3+CYW920829M2IPA2)
USB Type-A to Micro-B cable
Six jumper wires (five inches each)
Quick start guide
Supported Features
The board configuration supports the following hardware features:
Interface |
Controller |
Driver/Component |
|---|---|---|
NVIC |
on-chip |
nested vectored interrupt controller |
SYSTICK |
on-chip |
system clock |
GPIO |
on-chip |
GPIO |
UART |
on-chip |
serial port-polling; serial port-interrupt |
The default configuration can be found in the Kconfig
boards/infineon/cyw920829m2evk_02/cyw920829m2evk_02_defconfig
System Clock
The AIROC™ CYW20829 Bluetooth® MCU SoC is configured to use the internal IMO+FLL as a source for the system clock. Other sources for the system clock are provided in the SOC, depending on your system requirements.
Fetch Binary Blobs
cyw920829m2evk_02 board requires fetch binary files (e.g Bluetooth controller firmware).
To fetch Binary Blobs:
west blobs fetch hal_infineon
Build blinking led sample
Here is an example for building the Blinky sample application.
# From the root of the zephyr repository
west build -b cyw920829m2evk_02 samples/basic/blinky
Programming and Debugging
The CYW920829M2EVK-02 includes an onboard programmer/debugger (KitProg3) to provide debugging, flash programming, and serial communication over USB. Flash and debug commands use OpenOCD and require a custom Infineon OpenOCD version, that supports KitProg3, to be installed.
Infineon OpenOCD Installation
Both the full ModusToolbox and the ModusToolbox Programming Tools packages include Infineon OpenOCD. Installing either of these packages will also install Infineon OpenOCD. If neither package is installed, a minimal installation can be done by downloading the Infineon OpenOCD release for your system and manually extract the files to a location of your choice.
Note
Linux requires device access rights to be set up for KitProg3. This is handled automatically by the ModusToolbox and ModusToolbox Programming Tools installations. When doing a minimal installation, this can be done manually by executing the script openocd/udev_rules/install_rules.sh.
West Commands
The path to the installed Infineon OpenOCD executable must be available to the west tool commands. There are multiple ways of doing this. The example below uses a permanent CMake argument to set the CMake variable OPENOCD.
# Run west config once to set permanent CMake argument west config build.cmake-args -- -DOPENOCD=path/to/infineon/openocd/bin/openocd.exe # Do a pristine build once after setting CMake argument west build -b cyw920829m2evk_02 -p always samples/basic/blinky west flash west debug# Run west config once to set permanent CMake argument west config build.cmake-args -- -DOPENOCD=path/to/infineon/openocd/bin/openocd # Do a pristine build once after setting CMake argument west build -b cyw920829m2evk_02 -p always samples/basic/blinky west flash west debug
Once the gdb console starts after executing the west debug command, you may now set breakpoints and perform other standard GDB debugging on the CYW20829 CM33 core.