USB Type-C

USB Type-C. More...

Macros
#define	TC_V_SINK_DISCONNECT_MIN_MV   800
	VBUS minimum for a sink disconnect detection.
#define	TC_V_SINK_DISCONNECT_MAX_MV   3670
	VBUS maximum for a sink disconnect detection.
#define	TC_T_VBUS_ON_MAX_MS   275
	From entry to Attached.SRC until VBUS reaches the minimum vSafe5V threshold as measured at the source’s receptacle See Table 4-29 VBUS and VCONN Timing Parameters.
#define	TC_T_VBUS_OFF_MAX_MS   650
	From the time the Sink is detached until the Source removes VBUS and reaches vSafe0V (See USB PD).
#define	TC_T_VCONN_ON_MAX_MS   2
	From the time the Source supplied VBUS in the Attached.SRC state.
#define	TC_T_VCONN_ON_PA_MAX_MS   100
	From the time a Sink with accessory support enters the PoweredAccessory state until the Sink sources minimum VCONN voltage (see Table 4-5) See Table 4-29 VBUS and VCONN Timing Parameters.
#define	TC_T_VCONN_OFF_MAX_MS   35
	From the time that a Sink is detached or as directed until the VCONN supply is disconnected.
#define	TC_T_SINK_ADJ_MAX_MS   60
	Response time for a Sink to adjust its current consumption to be in the specified range due to a change in USB Type-C Current advertisement See Table 4-29 VBUS and VCONN Timing Parameters.
#define	TC_T_DRP_MIN_MS   50
	The minimum period a DRP shall complete a Source to Sink and back advertisement See Table 4-30 DRP Timing Parameters.
#define	TC_T_DRP_MAX_MS   100
	The maximum period a DRP shall complete a Source to Sink and back advertisement See Table 4-30 DRP Timing Parameters.
#define	TC_T_DRP_TRANSITION_MIN_MS   0
	The minimum time a DRP shall complete transitions between Source and Sink roles during role resolution See Table 4-30 DRP Timing Parameters.
#define	TC_T_DRP_TRANSITION_MAX_MS   1
	The maximum time a DRP shall complete transitions between Source and Sink roles during role resolution See Table 4-30 DRP Timing Parameters.
#define	TC_T_DRP_TRY_MIN_MS   75
	Minimum wait time associated with the Try.SRC state.
#define	TC_T_DRP_TRY_MAX_MS   150
	Maximum wait time associated with the Try.SRC state.
#define	TC_T_DRP_TRY_WAIT_MIN_MS   400
	Minimum wait time associated with the Try.SNK state.
#define	TC_T_DRP_TRY_WAIT_MAX_MS   800
	Maximum wait time associated with the Try.SNK state.
#define	TC_T_TRY_TIMEOUT_MIN_MS   550
	Minimum timeout for transition from Try.SRC to TryWait.SNK.
#define	TC_T_TRY_TIMEOUT_MAX_MS   1100
	Maximum timeout for transition from Try.SRC to TryWait.SNK.
#define	TC_T_VPD_DETACH_MIN_MS   10
	Minimum Time for a DRP to detect that the connected Charge-Through VCONNPowered USB Device has been detached, after VBUS has been removed.
#define	TC_T_VPD_DETACH_MAX_MS   20
	Maximum Time for a DRP to detect that the connected Charge-Through VCONNPowered USB Device has been detached, after VBUS has been removed.
#define	TC_T_CC_DEBOUNCE_MIN_MS   100
	Minimum time a port shall wait before it can determine it is attached See Table 4-31 CC Timing.
#define	TC_T_CC_DEBOUNCE_MAX_MS   200
	Maximum time a port shall wait before it can determine it is attached See Table 4-31 CC Timing.
#define	TC_T_PD_DEBOUNCE_MIN_MS   10
	Minimum time a Sink port shall wait before it can determine it is detached due to the potential for USB PD signaling on CC as described in the state definitions.
#define	TC_T_PD_DEBOUNCE_MAX_MS   20
	Maximum time a Sink port shall wait before it can determine it is detached due to the potential for USB PD signaling on CC as described in the state definitions.
#define	TC_T_TRY_CC_DEBOUNCE_MIN_MS   10
	Minimum Time a port shall wait before it can determine it is re-attached during the try-wait process.
#define	TC_T_TRY_CC_DEBOUNCE_MAX_MS   10
	Maximum Time a port shall wait before it can determine it is re-attached during the try-wait process.
#define	TC_T_ERROR_RECOVERY_SELF_POWERED_MIN_MS   25
	Minimum time a self-powered port shall remain in the ErrorRecovery state.
#define	TC_T_ERROR_RECOVERY_SOURCE_MIN_MS   240
	Minimum time a source shall remain in the ErrorRecovery state if it was sourcing VCONN in the previous state.
#define	TC_T_RP_VALUE_CHANGE_MIN_MS   10
	Minimum time a Sink port shall wait before it can determine there has been a change in Rp where CC is not BMC Idle or the port is unable to detect BMC Idle.
#define	TC_T_RP_VALUE_CHANGE_MAX_MS   20
	Maximum time a Sink port shall wait before it can determine there has been a change in Rp where CC is not BMC Idle or the port is unable to detect BMC Idle.
#define	TC_T_SRC_DISCONNECT_MIN_MS   0
	Minimum time a Source shall detect the SRC.Open state.
#define	TC_T_SRC_DISCONNECT_MAX_MS   20
	Maximum time a Source shall detect the SRC.Open state.
#define	TC_T_NO_TOGGLE_CONNECT_MIN_MS   0
	Minimum time to detect connection when neither Port Partner is toggling.
#define	TC_T_NO_TOGGLE_CONNECT_MAX_MS   5
	Maximum time to detect connection when neither Port Partner is toggling.
#define	TC_T_ONE_PORT_TOGGLE_CONNECT_MIN_MS   0
	Minimum time to detect connection when one Port Partner is toggling 0ms … dcSRC.DRP max * tDRP max + 2 * tNoToggleConnect).
#define	TC_T_ONE_PORT_TOGGLE_CONNECT_MAX_MS   80
	Maximum time to detect connection when one Port Partner is toggling 0ms … dcSRC.DRP max * tDRP max + 2 * tNoToggleConnect).
#define	TC_T_TWO_PORT_TOGGLE_CONNECT_MIN_MS   0
	Minimum time to detect connection when both Port Partners are toggling (0ms … 5 * tDRP max + 2 * tNoToggleConnect).
#define	TC_T_TWO_PORT_TOGGLE_CONNECT_MAX_MS   510
	Maximum time to detect connection when both Port Partners are toggling (0ms … 5 * tDRP max + 2 * tNoToggleConnect).
#define	TC_T_VPDCTDD_MIN_US   30
	Minimum time for a Charge-Through VCONN-Powered USB Device to detect that the Charge-Through source has disconnected from CC after VBUS has been removed, transition to CTUnattached.VPD, and re-apply its Rp termination advertising 3.0 A on the host port CC.
#define	TC_T_VPDCTDD_MAX_MS   5
	Maximum time for a Charge-Through VCONN-Powered USB Device to detect that the Charge-Through source has disconnected from CC after VBUS has been removed, transition to CTUnattached.VPD, and re-apply its Rp termination advertising 3.0 A on the host port CC.
#define	TC_T_VPDDISABLE_MIN_MS   25
	Minimum time for a Charge-Through VCONN-Powered USB Device shall remain in CTDisabled.VPD state.

Enumerations
enum	tc_cc_voltage_state {   TC_CC_VOLT_OPEN = 0 , TC_CC_VOLT_RA = 1 , TC_CC_VOLT_RD = 2 , TC_CC_VOLT_RP_DEF = 5 ,   TC_CC_VOLT_RP_1A5 = 6 , TC_CC_VOLT_RP_3A0 = 7 }
	CC Voltage status. More...
enum	tc_vbus_level { TC_VBUS_SAFE0V = 0 , TC_VBUS_PRESENT = 1 , TC_VBUS_REMOVED = 2 }
	VBUS level voltages. More...
enum	tc_rp_value { TC_RP_USB = 0 , TC_RP_1A5 = 1 , TC_RP_3A0 = 2 , TC_RP_RESERVED = 3 }
	Pull-Up resistor values. More...
enum	tc_cc_pull {   TC_CC_RA = 0 , TC_CC_RP = 1 , TC_CC_RD = 2 , TC_CC_OPEN = 3 ,   TC_RA_RD = 4 }
	CC pull resistors. More...
enum	tc_cable_plug { PD_PLUG_FROM_DFP_UFP = 0 , PD_PLUG_FROM_CABLE_VPD = 1 }
	Cable plug. More...
enum	tc_power_role { TC_ROLE_SINK = 0 , TC_ROLE_SOURCE = 1 }
	Power Delivery Power Role. More...
enum	tc_data_role { TC_ROLE_UFP = 0 , TC_ROLE_DFP = 1 , TC_ROLE_DISCONNECTED = 2 }
	Power Delivery Data Role. More...
enum	tc_cc_polarity { TC_POLARITY_CC1 = 0 , TC_POLARITY_CC2 = 1 }
	Polarity of the CC lines. More...
enum	tc_cc_states {   TC_CC_NONE = 0 , TC_CC_UFP_NONE = 1 , TC_CC_UFP_AUDIO_ACC = 2 , TC_CC_UFP_DEBUG_ACC = 3 ,   TC_CC_UFP_ATTACHED = 4 , TC_CC_DFP_ATTACHED = 5 , TC_CC_DFP_DEBUG_ACC = 6 }
	Possible port partner connections based on CC line states. More...

Detailed Description

USB Type-C.

Macro Definition Documentation

TC_T_CC_DEBOUNCE_MAX_MS

#define TC_T_CC_DEBOUNCE_MAX_MS   200

#include <zephyr/drivers/usb_c/usbc_tc.h>

Maximum time a port shall wait before it can determine it is attached See Table 4-31 CC Timing.

TC_T_CC_DEBOUNCE_MIN_MS

#define TC_T_CC_DEBOUNCE_MIN_MS   100

#include <zephyr/drivers/usb_c/usbc_tc.h>

Minimum time a port shall wait before it can determine it is attached See Table 4-31 CC Timing.

TC_T_DRP_MAX_MS

#define TC_T_DRP_MAX_MS   100

#include <zephyr/drivers/usb_c/usbc_tc.h>

The maximum period a DRP shall complete a Source to Sink and back advertisement See Table 4-30 DRP Timing Parameters.

TC_T_DRP_MIN_MS

#define TC_T_DRP_MIN_MS   50

#include <zephyr/drivers/usb_c/usbc_tc.h>

The minimum period a DRP shall complete a Source to Sink and back advertisement See Table 4-30 DRP Timing Parameters.

TC_T_DRP_TRANSITION_MAX_MS

#define TC_T_DRP_TRANSITION_MAX_MS   1

#include <zephyr/drivers/usb_c/usbc_tc.h>

The maximum time a DRP shall complete transitions between Source and Sink roles during role resolution See Table 4-30 DRP Timing Parameters.

TC_T_DRP_TRANSITION_MIN_MS

#define TC_T_DRP_TRANSITION_MIN_MS   0

#include <zephyr/drivers/usb_c/usbc_tc.h>

The minimum time a DRP shall complete transitions between Source and Sink roles during role resolution See Table 4-30 DRP Timing Parameters.

TC_T_DRP_TRY_MAX_MS

#define TC_T_DRP_TRY_MAX_MS   150

#include <zephyr/drivers/usb_c/usbc_tc.h>

Maximum wait time associated with the Try.SRC state.

See Table 4-30 DRP Timing Parameters

TC_T_DRP_TRY_MIN_MS

#define TC_T_DRP_TRY_MIN_MS   75

#include <zephyr/drivers/usb_c/usbc_tc.h>

Minimum wait time associated with the Try.SRC state.

See Table 4-30 DRP Timing Parameters

TC_T_DRP_TRY_WAIT_MAX_MS

#define TC_T_DRP_TRY_WAIT_MAX_MS   800

#include <zephyr/drivers/usb_c/usbc_tc.h>

Maximum wait time associated with the Try.SNK state.

See Table 4-30 DRP Timing Parameters

TC_T_DRP_TRY_WAIT_MIN_MS

#define TC_T_DRP_TRY_WAIT_MIN_MS   400

#include <zephyr/drivers/usb_c/usbc_tc.h>

Minimum wait time associated with the Try.SNK state.

See Table 4-30 DRP Timing Parameters

TC_T_ERROR_RECOVERY_SELF_POWERED_MIN_MS

#define TC_T_ERROR_RECOVERY_SELF_POWERED_MIN_MS   25

#include <zephyr/drivers/usb_c/usbc_tc.h>

Minimum time a self-powered port shall remain in the ErrorRecovery state.

See Table 4-31 CC Timing

TC_T_ERROR_RECOVERY_SOURCE_MIN_MS

#define TC_T_ERROR_RECOVERY_SOURCE_MIN_MS   240

#include <zephyr/drivers/usb_c/usbc_tc.h>

Minimum time a source shall remain in the ErrorRecovery state if it was sourcing VCONN in the previous state.

See Table 4-31 CC Timing

TC_T_NO_TOGGLE_CONNECT_MAX_MS

#define TC_T_NO_TOGGLE_CONNECT_MAX_MS   5

#include <zephyr/drivers/usb_c/usbc_tc.h>

Maximum time to detect connection when neither Port Partner is toggling.

See Table 4-31 CC Timing

TC_T_NO_TOGGLE_CONNECT_MIN_MS

#define TC_T_NO_TOGGLE_CONNECT_MIN_MS   0

#include <zephyr/drivers/usb_c/usbc_tc.h>

Minimum time to detect connection when neither Port Partner is toggling.

See Table 4-31 CC Timing

TC_T_ONE_PORT_TOGGLE_CONNECT_MAX_MS

#define TC_T_ONE_PORT_TOGGLE_CONNECT_MAX_MS   80

#include <zephyr/drivers/usb_c/usbc_tc.h>

Maximum time to detect connection when one Port Partner is toggling 0ms … dcSRC.DRP max * tDRP max + 2 * tNoToggleConnect).

See Table 4-31 CC Timing

TC_T_ONE_PORT_TOGGLE_CONNECT_MIN_MS

#define TC_T_ONE_PORT_TOGGLE_CONNECT_MIN_MS   0

#include <zephyr/drivers/usb_c/usbc_tc.h>

Minimum time to detect connection when one Port Partner is toggling 0ms … dcSRC.DRP max * tDRP max + 2 * tNoToggleConnect).

See Table 4-31 CC Timing

TC_T_PD_DEBOUNCE_MAX_MS

#define TC_T_PD_DEBOUNCE_MAX_MS   20

#include <zephyr/drivers/usb_c/usbc_tc.h>

Maximum time a Sink port shall wait before it can determine it is detached due to the potential for USB PD signaling on CC as described in the state definitions.

See Table 4-31 CC Timing

TC_T_PD_DEBOUNCE_MIN_MS

#define TC_T_PD_DEBOUNCE_MIN_MS   10

#include <zephyr/drivers/usb_c/usbc_tc.h>

Minimum time a Sink port shall wait before it can determine it is detached due to the potential for USB PD signaling on CC as described in the state definitions.

See Table 4-31 CC Timing

TC_T_RP_VALUE_CHANGE_MAX_MS

#define TC_T_RP_VALUE_CHANGE_MAX_MS   20

#include <zephyr/drivers/usb_c/usbc_tc.h>

Maximum time a Sink port shall wait before it can determine there has been a change in Rp where CC is not BMC Idle or the port is unable to detect BMC Idle.

See Table 4-31 CC Timing

TC_T_RP_VALUE_CHANGE_MIN_MS

#define TC_T_RP_VALUE_CHANGE_MIN_MS   10

#include <zephyr/drivers/usb_c/usbc_tc.h>

Minimum time a Sink port shall wait before it can determine there has been a change in Rp where CC is not BMC Idle or the port is unable to detect BMC Idle.

See Table 4-31 CC Timing

TC_T_SINK_ADJ_MAX_MS

#define TC_T_SINK_ADJ_MAX_MS   60

#include <zephyr/drivers/usb_c/usbc_tc.h>

Response time for a Sink to adjust its current consumption to be in the specified range due to a change in USB Type-C Current advertisement See Table 4-29 VBUS and VCONN Timing Parameters.

TC_T_SRC_DISCONNECT_MAX_MS

#define TC_T_SRC_DISCONNECT_MAX_MS   20

#include <zephyr/drivers/usb_c/usbc_tc.h>

Maximum time a Source shall detect the SRC.Open state.

The Source should detect the SRC.Open state as quickly as practical. See Table 4-31 CC Timing

TC_T_SRC_DISCONNECT_MIN_MS

#define TC_T_SRC_DISCONNECT_MIN_MS   0

#include <zephyr/drivers/usb_c/usbc_tc.h>

Minimum time a Source shall detect the SRC.Open state.

The Source should detect the SRC.Open state as quickly as practical. See Table 4-31 CC Timing

TC_T_TRY_CC_DEBOUNCE_MAX_MS

#define TC_T_TRY_CC_DEBOUNCE_MAX_MS   10

#include <zephyr/drivers/usb_c/usbc_tc.h>

Maximum Time a port shall wait before it can determine it is re-attached during the try-wait process.

See Table 4-31 CC Timing

TC_T_TRY_CC_DEBOUNCE_MIN_MS

#define TC_T_TRY_CC_DEBOUNCE_MIN_MS   10

#include <zephyr/drivers/usb_c/usbc_tc.h>

Minimum Time a port shall wait before it can determine it is re-attached during the try-wait process.

See Table 4-31 CC Timing

TC_T_TRY_TIMEOUT_MAX_MS

#define TC_T_TRY_TIMEOUT_MAX_MS   1100

#include <zephyr/drivers/usb_c/usbc_tc.h>

Maximum timeout for transition from Try.SRC to TryWait.SNK.

See Table 4-30 DRP Timing Parameters

TC_T_TRY_TIMEOUT_MIN_MS

#define TC_T_TRY_TIMEOUT_MIN_MS   550

#include <zephyr/drivers/usb_c/usbc_tc.h>

Minimum timeout for transition from Try.SRC to TryWait.SNK.

See Table 4-30 DRP Timing Parameters

TC_T_TWO_PORT_TOGGLE_CONNECT_MAX_MS

#define TC_T_TWO_PORT_TOGGLE_CONNECT_MAX_MS   510

#include <zephyr/drivers/usb_c/usbc_tc.h>

Maximum time to detect connection when both Port Partners are toggling (0ms … 5 * tDRP max + 2 * tNoToggleConnect).

See Table 4-31 CC Timing

TC_T_TWO_PORT_TOGGLE_CONNECT_MIN_MS

#define TC_T_TWO_PORT_TOGGLE_CONNECT_MIN_MS   0

#include <zephyr/drivers/usb_c/usbc_tc.h>

Minimum time to detect connection when both Port Partners are toggling (0ms … 5 * tDRP max + 2 * tNoToggleConnect).

See Table 4-31 CC Timing

TC_T_VBUS_OFF_MAX_MS

#define TC_T_VBUS_OFF_MAX_MS   650

#include <zephyr/drivers/usb_c/usbc_tc.h>

From the time the Sink is detached until the Source removes VBUS and reaches vSafe0V (See USB PD).

See Table 4-29 VBUS and VCONN Timing Parameters

TC_T_VBUS_ON_MAX_MS

#define TC_T_VBUS_ON_MAX_MS   275

#include <zephyr/drivers/usb_c/usbc_tc.h>

From entry to Attached.SRC until VBUS reaches the minimum vSafe5V threshold as measured at the source’s receptacle See Table 4-29 VBUS and VCONN Timing Parameters.

TC_T_VCONN_OFF_MAX_MS

#define TC_T_VCONN_OFF_MAX_MS   35

#include <zephyr/drivers/usb_c/usbc_tc.h>

From the time that a Sink is detached or as directed until the VCONN supply is disconnected.

See Table 4-29 VBUS and VCONN Timing Parameters

TC_T_VCONN_ON_MAX_MS

#define TC_T_VCONN_ON_MAX_MS   2

#include <zephyr/drivers/usb_c/usbc_tc.h>

From the time the Source supplied VBUS in the Attached.SRC state.

See Table 4-29 VBUS and VCONN Timing Parameters

TC_T_VCONN_ON_PA_MAX_MS

#define TC_T_VCONN_ON_PA_MAX_MS   100

#include <zephyr/drivers/usb_c/usbc_tc.h>

From the time a Sink with accessory support enters the PoweredAccessory state until the Sink sources minimum VCONN voltage (see Table 4-5) See Table 4-29 VBUS and VCONN Timing Parameters.

TC_T_VPD_DETACH_MAX_MS

#define TC_T_VPD_DETACH_MAX_MS   20

#include <zephyr/drivers/usb_c/usbc_tc.h>

Maximum Time for a DRP to detect that the connected Charge-Through VCONNPowered USB Device has been detached, after VBUS has been removed.

See Table 4-30 DRP Timing Parameters

TC_T_VPD_DETACH_MIN_MS

#define TC_T_VPD_DETACH_MIN_MS   10

#include <zephyr/drivers/usb_c/usbc_tc.h>

Minimum Time for a DRP to detect that the connected Charge-Through VCONNPowered USB Device has been detached, after VBUS has been removed.

See Table 4-30 DRP Timing Parameters

TC_T_VPDCTDD_MAX_MS

#define TC_T_VPDCTDD_MAX_MS   5

#include <zephyr/drivers/usb_c/usbc_tc.h>

Maximum time for a Charge-Through VCONN-Powered USB Device to detect that the Charge-Through source has disconnected from CC after VBUS has been removed, transition to CTUnattached.VPD, and re-apply its Rp termination advertising 3.0 A on the host port CC.

See Table 4-31 CC Timing

TC_T_VPDCTDD_MIN_US

#define TC_T_VPDCTDD_MIN_US   30

#include <zephyr/drivers/usb_c/usbc_tc.h>

Minimum time for a Charge-Through VCONN-Powered USB Device to detect that the Charge-Through source has disconnected from CC after VBUS has been removed, transition to CTUnattached.VPD, and re-apply its Rp termination advertising 3.0 A on the host port CC.

See Table 4-31 CC Timing

TC_T_VPDDISABLE_MIN_MS

#define TC_T_VPDDISABLE_MIN_MS   25

#include <zephyr/drivers/usb_c/usbc_tc.h>

Minimum time for a Charge-Through VCONN-Powered USB Device shall remain in CTDisabled.VPD state.

See Table 4-31 CC Timing

TC_V_SINK_DISCONNECT_MAX_MV

#define TC_V_SINK_DISCONNECT_MAX_MV   3670

#include <zephyr/drivers/usb_c/usbc_tc.h>

VBUS maximum for a sink disconnect detection.

See Table 4-3 VBUS Sink Characteristics

TC_V_SINK_DISCONNECT_MIN_MV

#define TC_V_SINK_DISCONNECT_MIN_MV   800

#include <zephyr/drivers/usb_c/usbc_tc.h>

VBUS minimum for a sink disconnect detection.

See Table 4-3 VBUS Sink Characteristics

Enumeration Type Documentation

tc_cable_plug

enum tc_cable_plug

#include <zephyr/drivers/usb_c/usbc_tc.h>

Cable plug.

See 6.2.1.1.7 Cable Plug. Only applies to SOP' and SOP". Replaced by pd_power_role for SOP packets.

Enumerator
PD_PLUG_FROM_DFP_UFP
PD_PLUG_FROM_CABLE_VPD

tc_cc_polarity

enum tc_cc_polarity

#include <zephyr/drivers/usb_c/usbc_tc.h>

Polarity of the CC lines.

Enumerator
TC_POLARITY_CC1	Use CC1 IO for Power Delivery communication.
TC_POLARITY_CC2	Use CC2 IO for Power Delivery communication.

tc_cc_pull

enum tc_cc_pull

#include <zephyr/drivers/usb_c/usbc_tc.h>

CC pull resistors.

Enumerator
TC_CC_RA	Ra Pull-Down resistor.
TC_CC_RP	Rp Pull-Up resistor.
TC_CC_RD	Rd Pull-Down resistor.
TC_CC_OPEN	No CC resistor.
TC_RA_RD	Ra and Rd Pull-Down resistor.

tc_cc_states

enum tc_cc_states

#include <zephyr/drivers/usb_c/usbc_tc.h>

Possible port partner connections based on CC line states.

Enumerator
TC_CC_NONE	No port partner attached.
TC_CC_UFP_NONE	From DFP perspective. No UFP accessory connected
TC_CC_UFP_AUDIO_ACC	UFP Audio accessory connected.
TC_CC_UFP_DEBUG_ACC	UFP Debug accessory connected.
TC_CC_UFP_ATTACHED	Plain UFP attached.
TC_CC_DFP_ATTACHED	From UFP perspective. Plain DFP attached
TC_CC_DFP_DEBUG_ACC	DFP debug accessory connected.

tc_cc_voltage_state

enum tc_cc_voltage_state

#include <zephyr/drivers/usb_c/usbc_tc.h>

CC Voltage status.

Enumerator
TC_CC_VOLT_OPEN	No port partner connection.
TC_CC_VOLT_RA	Port partner is applying Ra.
TC_CC_VOLT_RD	Port partner is applying Rd.
TC_CC_VOLT_RP_DEF	Port partner is applying Rp (0.5A)
TC_CC_VOLT_RP_1A5
TC_CC_VOLT_RP_3A0	Port partner is applying Rp (3.0A)

tc_data_role

enum tc_data_role

#include <zephyr/drivers/usb_c/usbc_tc.h>

Power Delivery Data Role.

Enumerator
TC_ROLE_UFP	Data role is an Upstream Facing Port.
TC_ROLE_DFP	Data role is a Downstream Facing Port.
TC_ROLE_DISCONNECTED	Port is disconnected.

tc_power_role

enum tc_power_role

#include <zephyr/drivers/usb_c/usbc_tc.h>

Power Delivery Power Role.

Enumerator
TC_ROLE_SINK	Power role is a sink.
TC_ROLE_SOURCE	Power role is a source.

tc_rp_value

enum tc_rp_value

#include <zephyr/drivers/usb_c/usbc_tc.h>

Pull-Up resistor values.

Enumerator
TC_RP_USB	Pull-Up resistor for a current of 900mA.
TC_RP_1A5	Pull-Up resistor for a current of 1.5A.
TC_RP_3A0	Pull-Up resistor for a current of 3.0A.
TC_RP_RESERVED	No Pull-Up resistor is applied.

tc_vbus_level

enum tc_vbus_level

#include <zephyr/drivers/usb_c/usbc_tc.h>

VBUS level voltages.

Enumerator
TC_VBUS_SAFE0V	VBUS is less than vSafe0V max.
TC_VBUS_PRESENT	VBUS is at least vSafe5V min.
TC_VBUS_REMOVED	VBUS is less than vSinkDisconnect max.