arduino-mkr-header
Vendor: Generic or vendor-independent
Description
GPIO pins exposing on Arduino MKR headers.
The Arduino MKR layout provides two headers on both edges of the board.
* One side of the 14-pin header is analog inputs and digital signals.
A1 to A6 is Analog input. The outside pin is AREF.
A0 that is next to AREF used as a DAC output pin too.
D0-D5 is a digital output.
* The other side 14-pin header is power supplies and peripheral interface.
There are 5V and VCC power supply, GND, and RESET pin. UART, I2C,
and SPI peripheral pins are also there. The end 2 pins are simple GPIO pins.
This binding provides a nexus mapping for 22 pins where parent pins 0
through 14 correspond to D0 through D21, and parent pins 15 through 21
correspond to A0 through A6, as depicted below.
- AREF 5V -
15 A0/D15/DAC0 VIN -
16 A1/D16 VCC -
17 A2/D17 GND -
18 A3/D18 RESET -
19 A4/D19 D14/TX 14
20 A5/D20 D13/RX 13
21 A6/D21 D12/SCL 12
0 D0 D11/SDA 11
1 D1 D10/CPIO 10
2 D2 D9/SCK 9
3 D3 D8/COPI 8
4 D4 D7 7
5 D5 D6 6
Properties
Properties not inherited from the base binding file.
Name |
Type |
Details |
|---|---|---|
|
|
This property is required. |
|
|
|
|
|
|
|
|
Number of items to expect in a GPIO specifier
This property is required. |
Deprecated properties not inherited from the base binding file.
(None)
Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “arduino-mkr-header” compatible.
Name |
Type |
Details |
|---|---|---|
|
|
indicates the operational status of a device
Legal values: See Important properties for more information. |
|
|
compatible strings
This property is required. See Important properties for more information. |
|
|
register space
See Important properties for more information. |
|
|
name of each register space
|
|
|
interrupts for device
See Important properties for more information. |
|
|
extended interrupt specifier for device
|
|
|
name of each interrupt
|
|
|
phandle to interrupt controller node
|
|
|
No description provided for this label
See Important properties for more information. |
|
|
Clock gate information
|
|
|
name of each clock
|
|
|
number of address cells in reg property
|
|
|
number of size cells in reg property
|
|
|
DMA channels specifiers
|
|
|
Provided names of DMA channel specifiers
|
|
|
IO channels specifiers
|
|
|
Provided names of IO channel specifiers
|
|
|
mailbox / IPM channels specifiers
|
|
|
Provided names of mailbox / IPM channel specifiers
|
|
|
Power domain specifiers
|
|
|
Provided names of power domain specifiers
|
|
|
Number of cells in power-domains property
|
|
|
Do not initialize device automatically on boot. Device should be manually
initialized using device_init().
|
|
|
Property to identify that a device can be used as wake up source.
When this property is provided a specific flag is set into the
device that tells the system that the device is capable of
wake up the system.
Wake up capable devices are disabled (interruptions will not wake up
the system) by default but they can be enabled at runtime if necessary.
|
|
|
Automatically configure the device for runtime power management after the
init function runs.
|
|
|
List of power states that will disable this device power.
|