nordic,nrf7002-qspi (on qspi bus)
Vendor: Nordic Semiconductor
Description
This is a representation of the nRF7002 Wi-Fi chip with QSPI interface.
Properties
Properties not inherited from the base binding file.
Name |
Type |
Details |
|---|---|---|
|
|
Maximum clock speed (in Hz) supported by the device.
This property is required. |
|
|
If specified, Use QSPI in quad mode (4 IO lines) otherwise in
SPI mode (2 IO lines - MOSI & MISO).
|
|
|
Number of clock cycles from the rising edge of the SPI clock
until the input serial data is sampled.
|
|
|
Set to indicate phase starts with asserted half-phase (CPHA=1).
The driver using this property must also use `cpol`.
|
|
|
Set to indicate that the clock leading edge is falling (CPOL=1).
The driver using this property requires also use `cpha`.
|
|
|
GPIO of the SoC controlling IO_VDD Control pin of the nRF70
This property is required. |
|
|
GPIO of the SoC controlling BUCK_EN pin of the nRF70
This property is required. |
|
|
GPIO of the SoC controlling the HOST_IRQ pin of the nRF70
This property is required. |
|
|
GPIO of the RF Switch to control SR RF output to either SR Antenna
or shared Antenna with Wi-Fi
|
|
|
Maximum transmit power allowed in 2.4GHz band for DSSS/CCK rates
This property is required. |
|
|
Maximum transmit power allowed in 2.4GHz band for MCS0
This property is required. |
|
|
Maximum transmit power allowed in 2.4GHz band for MCS7
This property is required. |
|
|
Maximum transmit power allowed in 5GHz band MCS0 low sub-band
This property is required. |
|
|
Maximum transmit power allowed in 5GHz band MCS7 low sub-band
This property is required. |
|
|
Maximum transmit power allowed in 5GHz band MCS0 mid sub-band
This property is required. |
|
|
Maximum transmit power allowed in 5GHz band MCS7 mid sub-band
This property is required. |
|
|
Maximum transmit power allowed in 5GHz band MCS0 high sub-band
This property is required. |
|
|
Maximum transmit power allowed in 5GHz band MCS7 high sub-band
|
Deprecated properties not inherited from the base binding file.
(None)
Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “nordic,nrf7002-qspi” compatible.
Name |
Type |
Details |
|---|---|---|
|
|
register space
This property is required. See Important properties for more information. |
|
|
indicates the operational status of a device
Legal values: See Important properties for more information. |
|
|
compatible strings
This property is required. See Important properties for more information. |
|
|
name of each register space
|
|
|
interrupts for device
See Important properties for more information. |
|
|
extended interrupt specifier for device
|
|
|
name of each interrupt
|
|
|
phandle to interrupt controller node
|
|
|
No description provided for this label
See Important properties for more information. |
|
|
Clock gate information
|
|
|
name of each clock
|
|
|
number of address cells in reg property
|
|
|
number of size cells in reg property
|
|
|
DMA channels specifiers
|
|
|
Provided names of DMA channel specifiers
|
|
|
IO channels specifiers
|
|
|
Provided names of IO channel specifiers
|
|
|
mailbox / IPM channels specifiers
|
|
|
Provided names of mailbox / IPM channel specifiers
|
|
|
Power domain specifiers
|
|
|
Provided names of power domain specifiers
|
|
|
Number of cells in power-domains property
|
|
|
Do not initialize device automatically on boot. Device should be manually
initialized using device_init().
|
|
|
Property to identify that a device can be used as wake up source.
When this property is provided a specific flag is set into the
device that tells the system that the device is capable of
wake up the system.
Wake up capable devices are disabled (interruptions will not wake up
the system) by default but they can be enabled at runtime if necessary.
|
|
|
Automatically configure the device for runtime power management after the
init function runs.
|
|
|
List of power states that will disable this device power.
|