Bluetooth: HCI UART based on ASYNC UART
Expose a Zephyr Bluetooth Controller over a standard Bluetooth HCI UART interface.
This sample performs the same basic function as the HCI UART sample, but it uses the UART_ASYNC_API instead of UART_INTERRUPT_DRIVEN API. Not all boards implement both UART APIs, so the board support of the HCI UART sample may be different.
Requirements
A board with BLE support
Default UART settings
By default the controller builds use the following settings:
Baudrate: 1Mbit/s
8 bits, no parity, 1 stop bit
Hardware Flow Control (RTS/CTS) enabled
Building and Running
This sample can be found under samples/bluetooth/hci_uart_async in the Zephyr tree and is built as a standard Zephyr application.
Using the controller with emulators and BlueZ
The instructions below show how to use a Nordic nRF5x device as a Zephyr BLE controller and expose it to Linux’s BlueZ.
First, make sure you have a recent BlueZ version installed by following the instructions in the Using BlueZ with Zephyr section.
Now build and flash the sample for the Nordic nRF5x board of your choice. All of the Nordic Development Kits come with a Segger IC that provides a debugger interface and a CDC ACM serial port bridge. More information can be found in Nordic nRF5x Segger J-Link.
For example, to build for the nRF52832 Development Kit:
# From the root of the zephyr repository
west build -b nrf52dk/nrf52832 samples/bluetooth/hci_uart_async
west flash
Using the controller with QEMU or native_sim
In order to use the HCI UART controller with QEMU or native_sim you will need to attach it to the Linux Host first. To do so simply build the sample and connect the UART to the Linux machine, and then attach it with this command:
sudo btattach -B /dev/ttyACM0 -S 1000000 -R
Note
Depending on the serial port you are using you will need to modify the
/dev/ttyACM0 string to point to the serial device your controller is
connected to.
Note
The -R flag passed to btattach instructs the kernel to avoid
interacting with the controller and instead just be aware of it in order
to proxy it to QEMU later.
If you are running btmon you should see a brief log showing how the
Linux kernel identifies the attached controller.
Once the controller is attached follow the instructions in the Running on QEMU or native_sim section to use QEMU with it.
Using the controller with BlueZ
In order to use the HCI UART controller with BlueZ you will need to attach it to the Linux Host first. To do so simply build the sample and connect the UART to the Linux machine, and then attach it with this command:
sudo btattach -B /dev/ttyACM0 -S 1000000
Note
Depending on the serial port you are using you will need to modify the
/dev/ttyACM0 string to point to the serial device your controller is
connected to.
If you are running btmon you should see a comprehensive log showing how
BlueZ loads and initializes the attached controller.
Once the controller is attached follow the instructions in the Using Zephyr-based Controllers with BlueZ section to use BlueZ with it.
Debugging the controller
The sample can be debugged using RTT since the UART is reserved used by this application. To enable debug over RTT the debug configuration file can be used.
west build samples/bluetooth/hci_uart_async -- -DEXTRA_CONFIG='debug.mixin.conf'
Then attach RTT as described here: Using Segger J-Link
Using the controller with the Zephyr host
This describes how to hook up a board running this sample to a board running an application that uses the Zephyr host.
On the controller side, the zephyr,bt-c2h-uart DTS property (in the chosen block) is used to select which uart device to use. For example if we want to keep the console logs, we can keep console on uart0 and the HCI on uart1 like so:
/ {
chosen {
zephyr,console = &uart0;
zephyr,shell-uart = &uart0;
zephyr,bt-c2h-uart = &uart1;
};
};
On the host application, some config options need to be used to select the H4 driver instead of the built-in controller:
CONFIG_BT_HCI=y
CONFIG_BT_CTLR=n
Similarly, the zephyr,bt-hci DTS property selects which HCI instance to use. The UART needs to have as its child node a HCI UART node:
/ {
chosen {
zephyr,console = &uart0;
zephyr,shell-uart = &uart0;
zephyr,bt-hci = &bt_hci_uart;
};
};
&uart1 {
status = "okay";
bt_hci_uart: bt_hci_uart {
compatible = "zephyr,bt-hci-uart";
status = "okay";
};
};