RD-RW612-BGA
Overview
The RW612 is a highly integrated, low-power tri-radio wireless MCU with an integrated 260 MHz ARM Cortex-M33 MCU and Wi-Fi 6 + Bluetooth Low Energy (LE) 5.3 / 802.15.4 radios designed for a broad array of applications, including connected smart home devices, gaming controllers, enterprise and industrial automation, smart accessories and smart energy.
The RW612 MCU subsystem includes 1.2 MB of on-chip SRAM and a high-bandwidth Quad SPI interface with an on-the-fly decryption engine for securely accessing off-chip XIP flash.
The advanced design of the RW612 delivers tight integration, low power and highly secure operation in a space- and cost-efficient wireless MCU requiring only a single 3.3 V power supply.
Hardware
260 MHz ARM Cortex-M33, tri-radio cores for Wifi 6 + BLE 5.3 + 802.15.4
1.2 MB on-chip SRAM
Supported Features
Interface |
Controller |
Driver/Component |
|---|---|---|
NVIC |
on-chip |
nested vector interrupt controller |
SYSTICK |
on-chip |
systick |
MCI_IOMUX |
on-chip |
pinmux |
GPIO |
on-chip |
gpio |
USART |
on-chip |
serial |
DMA |
on-chip |
dma |
SPI |
on-chip |
spi |
I2C |
on-chip |
i2c |
FLEXSPI |
on-chip |
flash/memc |
TRNG |
on-chip |
entropy |
DMIC |
on-chip |
dmic |
LCDIC |
on-chip |
mipi-dbi |
WWDT |
on-chip |
watchdog |
USBOTG |
on-chip |
usb |
CTIMER |
on-chip |
counter |
SCTIMER |
on-chip |
pwm |
MRT |
on-chip |
counter |
OS_TIMER |
on-chip |
os timer |
PM |
on-chip |
power management; uses SoC Power Modes 1 and 2 |
BLE |
on-chip |
Bluetooth |
ADC |
on-chip |
adc |
DAC |
on-chip |
dac |
ENET |
on-chip |
ethernet |
The default configuration can be found in the defconfig file:
Other hardware features are not currently supported
Display Support
The rd_rw612_bga board supports several in-tree display modules. Setup for each module is described below:
GoWorld 16880 LCM
This module does not connect directly to the board, and must be connected via an adapter board and jumper wires. Connections are described in boards/nxp/rd_rw612_bga/dts/goworld_16880_lcm.overlay. The display sample can be built for this board like so:
west build -b rd_rw612_bga samples/drivers/display -- -DDTC_OVERLAY_FILE=goworld_16880_lcm.overlay
Adafruit 2.8 TFT
The Adafruit 2.8” TFT Touch Shield v2 connects to the board’s Arduino headers directly, but some modifications are required (see boards/shields/adafruit_2_8_tft_touch_v2/boards/rd_rw612_bga.overlay for a list). The display sample can be built for this module like so:
west build -b rd_rw612_bga --shield adafruit_2_8_tft_touch_v2 samples/drivers/display
NXP LCD_PAR_S035
The NXP LCD_PAR_S035 TFT LCD Module does not connect directly to the board, and must be connected via jumper wires. Connections and required board changes are described in boards/shields/lcd_par_s035/boards/rd_rw612_bga.overlay. The display sample can be built for the module like so:
west build -b rd_rw612_bga --shield lcd_par_s035_8080 samples/drivers/display
Fetch Binary Blobs
To support Bluetooth, rd_rw612_bga requires fetching binary blobs, which can be achieved by running the following command:
west blobs fetch hal_nxp
Programming and Debugging
Build and flash applications as usual (see Building an Application and Run an Application for more details).
Configuring a Debug Probe
A debug probe is used for both flashing and debugging the board. This board is configured by default to use the JLink Firmware.
Configuring a Console
Connect a USB cable from your PC to J7, and use the serial terminal of your choice (minicom, putty, etc.) with the following settings:
Speed: 115200
Data: 8 bits
Parity: None
Stop bits: 1
Flashing
Here is an example for the Hello World application. This example uses the J-Link Debug Host Tools as default.
# From the root of the zephyr repository
west build -b rd_rw612_bga samples/hello_world
west flash
Open a serial terminal, reset the board (press the RESET button), and you should see the following message in the terminal:
***** Booting Zephyr OS v3.4.0 *****
Hello World! rd_rw612_bga
Debugging
Here is an example for the Hello World application. This example uses the J-Link Debug Host Tools as default.
# From the root of the zephyr repository
west build -b rd_rw612_bga samples/hello_world
west debug
Open a serial terminal, step through the application in your debugger, and you should see the following message in the terminal:
***** Booting Zephyr OS zephyr-v3.6.0 *****
Hello World! rd_rw612_bga
Bluetooth
BLE functionality requires to fetch binary blobs, so make sure to follow
the Fetch Binary Blobs section first.
rd_rw612_bga platform supports the monolithic feature. The required binary blob
<zephyr workspace>/modules/hal/nxp/zephyr/blobs/rw61x_sb_ble_a2.bin will be linked
with the application image directly, forming one single monolithic image.
Board variants
Ethernet
To use ethernet on the RD_RW612_BGA board, you first need to make the following modifications to the board hardware:
Add resistors:
R485
R486
R487
R488
R489
R491
R490
Remove resistors:
R522
R521
R520
R524
R523
R508
R505
Then, build for the board target rd_rw612_bga//ethernet.