The latest development version of this page may be more current than this released 4.0.0 version.

UCANS32K1SIC

Overview

NXP UCANS32K1SIC [1] is a CAN signal improvement capability (SIC) evaluation board designed for both automotive and industrial applications. The UCANS32K1SIC provides two CAN SIC interfaces and is based on the 32-bit Arm Cortex-M4F NXP S32K146 [2] microcontroller.

Hardware

  • NXP S32K146

    • Arm Cortex-M4F @ up to 112 Mhz

    • 1 MB Flash

    • 128 KB SRAM

    • up to 127 I/Os

    • 3x FlexCAN with 2x FD

    • eDMA, 12-bit ADC, MPU, ECC and more.

  • Interfaces:

    • DCD-LZ debug interface with SWD + Console / UART

    • Dual CAN FD PHYs with dual connectors for daisy chain operation

    • JST-GH DroneCode compliant standard connectors and I/O headers

    • user RGB LED and button.

More information about the hardware and design resources can be found at NXP UCANS32K1SIC [1] website.

Supported Features

The ucans32k1sic board configuration supports the following hardware features:

Interface

Controller

Driver/Component

SYSMPU

on-chip

mpu

PORT

on-chip

pinctrl

GPIO

on-chip

gpio

LPUART

on-chip

serial

LPI2C

on-chip

i2c

LPSPI

on-chip

spi

FTM

on-chip

pwm

FlexCAN

on-chip

can

Watchdog

on-chip

watchdog

RTC

on-chip

counter

ADC

on-chip

adc

The default configuration can be found in the Kconfig file boards/nxp/ucans32k1sic/ucans32k1sic_defconfig.

Connections and IOs

This board has 5 GPIO ports named from gpioa to gpioe.

Pin control can be further configured from your application overlay by adding children nodes with the desired pinmux configuration to the singleton node pinctrl. Supported properties are described in dts/bindings/pinctrl/nxp,kinetis-pinctrl.yaml.

LEDs

The UCANS32K1SIC board has one user RGB LED that can be used either as a GPIO LED or as a PWM LED.

RGB LED as GPIO LED

Devicetree node

Devicetree alias

Label

Pin

led1_red

led0

LED1_RGB_RED

PTD15

led1_green

led1

LED1_RGB_GREEN

PTD16

led1_blue

led2

LED1_RGB_BLUE

PTD0
RGB LED as PWM LED

Devicetree node

Devicetree alias

Label

Pin

led1_red_pwm

pwm-led0 / red-pwm-led

LED1_RGB_RED_PWM

PTD15 / FTM0_CH0

led1_green_pwm

pwm-led1 / green-pwm-led

LED1_RGB_GREEN_PWM

PTD16 / FTM0_CH1

led1_blue_pwm

pwm-led2 / blue-pwm-led

LED1_RGB_BLUE_PWM

PTD0 / FTM0_CH2

The user can control the LEDs in any way. An output of 0 illuminates the LED.

Buttons

The UCANS32K1SIC board has one user button:

Devicetree node

Label

Pin

sw0 / button_3

SW3

PTD15

Serial Console

The serial console is provided via lpuart1 on the 7-pin DCD-LZ debug connector P6.

Connector

Pin

Pin Function

P6.2

PTC7

LPUART1_TX

P6.3

PTC6

LPUART1_RX

System Clock

The Arm Cortex-M4F core is configured to run at 80 MHz (RUN mode).

Programming and Debugging

Applications for the ucans32k1sic board can be built in the usual way as documented in Building an Application.

This board configuration supports Lauterbach TRACE32 [3] and SEGGER J-Link [4] West runners for flashing and debugging applications. Follow the steps described in Lauterbach TRACE32 Debug Host Tools and J-Link Debug Host Tools, to setup the flash and debug host tools for these runners, respectively. The default runner is J-Link.

Flashing

Run the west flash command to flash the application using SEGGER J-Link. Alternatively, run west flash -r trace32 to use Lauterbach TRACE32.

The Lauterbach TRACE32 runner supports additional options that can be passed through command line:

west flash -r trace32 --startup-args elfFile=<elf_path> loadTo=<flash/sram>
   eraseFlash=<yes/no> verifyFlash=<yes/no>

Where:

  • <elf_path> is the path to the Zephyr application ELF in the output directory

  • loadTo=flash loads the application to the SoC internal program flash (CONFIG_XIP must be set), and loadTo=sram load the application to SRAM. The default is flash.

  • eraseFlash=yes erases the whole content of SoC internal flash before the application is downloaded to either Flash or SRAM. This routine takes time to execute. The default is no.

  • verifyFlash=yes verify the SoC internal flash content after programming (use together with loadTo=flash). The default is no.

For example, to erase and verify flash content:

west flash -r trace32 --startup-args elfFile=build/zephyr/zephyr.elf loadTo=flash eraseFlash=yes verifyFlash=yes

Debugging

Run the west debug command to start a GDB session using SEGGER J-Link. Alternatively, run west debug -r trace32 to launch the Lauterbach TRACE32 software debugging interface.

References