LPCXpresso55S36
Overview
The LPCXpresso55S36 board provides the ideal platform for evaluation of the LPC55S3x/LPC553x MCU family, based on the Arm® Cortex®-M33 architecture. Arduino® UNO compatible shield connectors are included, with additional expansion ports around the Arduino footprint, along with a PMod/host interface port and MikroElektronika Click module site.
Hardware
LPC55S36 Arm® Cortex®-M33 microcontroller running at up to 150 MHz
256 KB flash and 96 KB SRAM on-chip
LPC-Link2 debug high speed USB probe with VCOM port
I2C and SPI USB bridging to the LPC device via LPC-Link2 probe
MikroElektronika Click expansion option
LPCXpresso expansion connectors compatible with Arduino UNO
PMod compatible expansion / host connector
Reset, ISP, wake, and user buttons for easy testing of software functionality
Tri-color LED
Full-speed USB device / host port
High-speed USB device / host port
UART header for external serial to USB cable
CAN Transceiver
Stereo audio codec with in/out line
For more information about the LPC55S36 SoC and LPCXPresso55S36 board, see:
Supported Features
NXP considers the LPCXpresso55S36 as a superset board for the LPC55(S)3x family of MCUs. This board is a focus for NXP’s Full Platform Support for Zephyr, to better enable the entire LPC55(S)3x family. NXP prioritizes enabling this board with new support for Zephyr features. The lpcxpresso55s36 board configuration supports the hardware features below. Another similar superset board is the LPCXPRESSO55S69, and that board may have additional features already supported, which can also be re-used on this lpcxpresso55s36 board:
Interface |
Controller |
Driver/Component |
|---|---|---|
NVIC |
on-chip |
nested vector interrupt controller |
SYSTICK |
on-chip |
systick |
IOCON |
on-chip |
pinmux |
GPIO |
on-chip |
gpio |
USART |
on-chip |
serial port-polling; serial port-interrupt |
CLOCK |
on-chip |
clock_control |
CAN |
on-chip |
canbus |
IAP |
on-chip |
flash |
PWM |
on-chip |
pwm |
USB FS |
on-chip |
USB Full Speed device |
DAC |
on-chip |
dac |
Other hardware features are not currently enabled.
Currently available targets for this board are:
lpcxpresso55s36
Connections and IOs
The LPC55S36 SoC has IOCON registers, which can be used to configure the functionality of a pin.
Name |
Function |
Usage |
|---|---|---|
PIO0_17 |
GPIO |
USR SW3 |
PIO0_22 |
GPIO |
GREEN LED |
PIO0_28 |
GPIO |
RED LED |
PIO0_29 |
USART |
USART RX |
PIO0_30 |
USART |
USART TX |
PIO1_11 |
GPIO |
BLUE_LED |
PIO1_18 |
GPIO |
Wakeup SW1 |
PIO1_20 |
FLEXPPWM0_PWM0_A |
pwm |
PIO1_17 |
FLEXPPWM0_PWM0_B |
pwm |
PIO1_6 |
FLEXPPWM0_PWM1_A |
pwm |
PIO1_22 |
FLEXPPWM0_PWM1_B |
pwm |
PIO1_8 |
FLEXPPWM0_PWM2_A |
pwm |
PIO1_4 |
FLEXPPWM0_PWM2_B |
pwm |
PIO1_21 |
FLEXPPWM1_PWM0_A |
pwm |
PIO0_3 |
FLEXPPWM1_PWM0_B |
pwm |
PIO1_23 |
FLEXPPWM1_PWM1_A |
pwm |
PIO0_21 |
FLEXPPWM1_PWM1_B |
pwm |
PIO1_25 |
FLEXPPWM1_PWM2_A |
pwm |
PIO0_31 |
FLEXPPWM1_PWM2_B |
pwm |
PIO1_2 |
CAN0_TXD |
CAN TX |
PIO1_3 |
CAN0_RXD |
CAN RX |
PIO0_22 |
USB0_VBUS |
USBFS VBUS |
System Clock
The LPC55S36 SoC is configured to use PLL1 clocked from the external 24MHz crystal, running at 144MHz as a source for the system clock. When the flash controller is enabled, the core clock will be reduced to 96MHz. Other sources for the system clock are provided in the SOC, depending on your system requirements.
Serial Port
The LPC55S36 SoC has 8 FLEXCOMM interfaces for serial communication. One is configured as USART for the console and the remaining are not used.
Programming and Debugging
Build and flash applications as usual (see Building an Application and Run an Application for more details).
Configuring a Debug Probe
A debug probe is used for both flashing and debugging the board. This board is
configured by default to use the integrated MCU-Link Onboard Debug Probe
in the CMSIS-DAP mode. To use this probe with Zephyr, you need to install the
LinkServer Debug Host Tools and make sure they are in your search path.
Then, use the linkserver runner option to flash and debug the board. Refer
to the detailed overview about Application Debugging for additional
information.
The integrated MCU-Link hardware can also be used as a J-Link probe with a firmware update, as described in MCU-Link JLink Onboard Debug Probe. The J-Link Debug Host Tools should be available in this case.
Configuring a Console
Connect a USB cable from your PC to J1 (LINK2), and use the serial terminal of your choice (minicom, putty, etc.) with the following settings:
Speed: 115200
Data: 8 bits
Parity: None
Stop bits: 1
Flashing
Here is an example for the Hello World application.
# From the root of the zephyr repository
west build -b lpcxpresso55s36 samples/hello_world
west flash
Open a serial terminal, reset the board (press the RESET button), and you should see the following message in the terminal:
***** Booting Zephyr OS v2.2.0 *****
Hello World! lpcxpresso55s36
Debugging
Here is an example for the Hello World application.
# From the root of the zephyr repository
west build -b lpcxpresso55s36 samples/hello_world
west debug
Open a serial terminal, step through the application in your debugger, and you should see the following message in the terminal:
***** Booting Zephyr OS zephyr-v2.2.0 *****
Hello World! lpcxpresso55s36