orisetech,otm8009a (on mipi-dsi bus)

Note

An implementation of a driver matching this compatible is available in drivers/display/display_otm8009a.c.

Description

Orise Tech OTM8009A Panel

Properties

Properties not inherited from the base binding file.

Name	Type	Details
`reset-gpios`	`phandle-array`	The RESETn pin is asserted to disable the sensor causing a hard reset. The sensor receives this as an active-low signal.
`bl-gpios`	`phandle-array`	The BLn pin is asserted to control the backlight of the panel. The sensor receives this as an active-high signal.
`rotation`	`int`	Display rotation (CW) in degrees. Defaults to 0, display default. Legal values: `0`, `90`, `180`, `270`
`data-lanes`	`array`	Number of data lanes. This property is required.
`pixel-format`	`int`	Pixel format. Available formats in dt-bindings/mipi_dsi/mipi_dsi.h. This property is required.
`height`	`int`	Height of the panel driven by the controller, with the units in pixels. This property is required.
`width`	`int`	Width of the panel driven by the controller, with the units in pixels. This property is required.

Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “orisetech,otm8009a” compatible.

Name	Type	Details
`reg`	`array`	register space This property is required. See Important properties for more information.
`status`	`string`	indicates the operational status of a device Legal values: `'ok'`, `'okay'`, `'disabled'`, `'reserved'`, `'fail'`, `'fail-sss'` See Important properties for more information.
`compatible`	`string-array`	compatible strings This property is required. See Important properties for more information.
`reg-names`	`string-array`	name of each register space
`interrupts`	`array`	interrupts for device See Important properties for more information.
`interrupts-extended`	`compound`	extended interrupt specifier for device
`interrupt-names`	`string-array`	name of each interrupt
`interrupt-parent`	`phandle`	phandle to interrupt controller node
`label`	`string`	Human readable string describing the device (used as device_get_binding() argument) See Important properties for more information. This property is deprecated.
`clocks`	`phandle-array`	Clock gate information
`clock-names`	`string-array`	name of each clock
`#address-cells`	`int`	number of address cells in reg property
`#size-cells`	`int`	number of size cells in reg property
`dmas`	`phandle-array`	DMA channels specifiers
`dma-names`	`string-array`	Provided names of DMA channel specifiers
`io-channels`	`phandle-array`	IO channels specifiers
`io-channel-names`	`string-array`	Provided names of IO channel specifiers
`mboxes`	`phandle-array`	mailbox / IPM channels specifiers
`mbox-names`	`string-array`	Provided names of mailbox / IPM channel specifiers
`power-domains`	`phandle-array`	Power domain specifiers
`power-domain-names`	`string-array`	Provided names of power domain specifiers
`#power-domain-cells`	`int`	Number of cells in power-domains property
`zephyr,deferred-init`	`boolean`	Do not initialize device automatically on boot. Device should be manually initialized using device_init().
`wakeup-source`	`boolean`	Property to identify that a device can be used as wake up source. When this property is provided a specific flag is set into the device that tells the system that the device is capable of wake up the system. Wake up capable devices are disabled (interruptions will not wake up the system) by default but they can be enabled at runtime if necessary.
`zephyr,pm-device-runtime-auto`	`boolean`	Automatically configure the device for runtime power management after the init function runs.
`zephyr,disabling-power-states`	`phandles`	List of power states that will disable this device power.