raydium,rm67162 (on mipi-dbi bus)

Description

Raydium RM67162 display controller on MIPI DBI bus

The Raydium RM67162 is a 16.7M colors OLED controller.

Properties

Properties not inherited from the base binding file.

Name

Type

Details

mipi-mode

string

MIPI DBI mode in use. The RM67162 has 3-wire and 4-wire SPI and an
8-bit 8080 bus interface. These definitions should match those in
dt-bindings/mipi_dbi/mipi_dbi.h

This property is required.

Legal values: MIPI_DBI_MODE_SPI_3WIRE, MIPI_DBI_MODE_SPI_4WIRE, MIPI_DBI_MODE_6800_BUS_16_BIT, MIPI_DBI_MODE_6800_BUS_9_BIT, MIPI_DBI_MODE_6800_BUS_8_BIT, MIPI_DBI_MODE_8080_BUS_16_BIT, MIPI_DBI_MODE_8080_BUS_9_BIT, MIPI_DBI_MODE_8080_BUS_8_BIT

pixel-format

int

Initial pixel format. The MIPI DBI interfaces of the controller are
byte wide and receive 16-bit pixels most significant byte first.

Default value: 32

Legal values: 1, 32

duplex

int

SPI Duplex mode, full or half. By default it's always full duplex thus 0
as this is, by far, the most common mode.
Selecting half duplex allows to use the SPI controller's SDO as a bidirectional line,
typically used when only one data line is connected.
Use the macros, not the actual enum value. Here is the concordance
list (see dt-bindings/spi/spi.h)
  0    SPI_FULL_DUPLEX
  2048 SPI_HALF_DUPLEX

Default value: 0

mipi-cpol

boolean

SPI clock polarity which indicates the clock idle state.
If it is used, the clock idle state is logic high; otherwise, low.

mipi-cpha

boolean

SPI clock phase that indicates on which edge data is sampled.
If it is used, data is sampled on the second edge; otherwise, on the first edge.

mipi-hold-cs

boolean

In some cases, it is necessary for the controller to manage SPI chip select
under software control, so that multiple spi transactions can be performed
without releasing it. A typical use case is variable length SPI packets
where the first spi transaction reads the length and the second spi transaction
reads length bytes.

mipi-max-frequency

int

Maximum clock frequency of device's MIPI interface in Hz

color-coding

string

Color coding for MIPI DBI Type A or Type B(6800/8080) interface. These definitions
should match those in dt-bindings/mipi_dbi/mipi_dbi.h

Legal values: MIPI_DBI_MODE_RGB332, MIPI_DBI_MODE_RGB444, MIPI_DBI_MODE_RGB565, MIPI_DBI_MODE_RGB666_1, MIPI_DBI_MODE_RGB666_2, MIPI_DBI_MODE_RGB888_1, MIPI_DBI_MODE_RGB888_2

te-mode

string

MIPI DBI tearing enable signal mode. Defaults to disabled.

Default value: MIPI_DBI_TE_NO_EDGE

Legal values: MIPI_DBI_TE_NO_EDGE, MIPI_DBI_TE_RISING_EDGE, MIPI_DBI_TE_FALLING_EDGE

te-delay

int

Delay in microseconds to wait before transmitting display data after a
tearing enable synchronization signal is seen. Defaults to 0 since most
controllers will not need a delay.

Default value: 0

supply-gpios

phandle-array

GPIO specifier that controls power to the device.

This property should be provided when the device has a dedicated
switch that controls power to the device.  The supply state is
entirely the responsibility of the device driver.

Contrast with vin-supply.

vin-supply

phandle

Reference to the regulator that controls power to the device.
The referenced devicetree node must have a regulator compatible.

This property should be provided when device power is supplied
by a shared regulator.  The supply state is dependent on the
request status of all devices fed by the regulator.

Contrast with supply-gpios.  If both properties are provided
then the regulator must be requested before the supply GPIOS is
set to an active state, and the supply GPIOS must be set to an
inactive state before releasing the regulator.

init-sequence

string

Manufacturer settings written to the controller at initialization.
They come from the panel vendor and differ between panels.

- g1120b0mipi: 400x392 panel of the G1120B0MIPI module
- e1918am3.a: 1.91" 240x536 E1918AM3.A panel, used on the LilyGO
  T-Display S3 AMOLED boards

Default value: g1120b0mipi

Legal values: g1120b0mipi, e1918am3.a

rotation

int

Initial display rotation (clockwise) in degrees. The width and height
properties describe the panel before this rotation is applied.

Default value: 0

Legal values: 0, 90, 180, 270

height

int

Height of the panel driven by the controller, with the units in pixels.

This property is required.

width

int

Width of the panel driven by the controller, with the units in pixels.

This property is required.