sitronix,st7789v (on mipi-dbi bus)

Vendor: Sitronix Technology Corporation

Note

An implementation of a driver matching this compatible is available in drivers/display/display_st7789v.c.

Description

ST7789V 320x240 display controller

Properties

Node specific propertiesDeprecated node specific propertiesBase properties

Properties not inherited from the base binding file.

Name	Type	Details
x-offset	int	The column offset in pixels of the LCD to the controller memory This property is required.
y-offset	int	The row offset in pixels of the LCD to the controller memory This property is required.
vcom	int	VCOM Setting This property is required.
gctrl	int	Gate Control This property is required.
vrhs	int	VRH Setting
vdvs	int	VDV Setting
mdac	int	Memory Data Access Control This property is required.
lcm	int	LCM Setting This property is required.
colmod	int	Interface Pixel Format This property is required.
gamma	int	Gamma Setting This property is required.
inversion-off	boolean	Inversion Off
porch-param	uint8-array	Porch Setting This property is required.
cmd2en-param	uint8-array	Command 2 Enable Parameter This property is required.
pwctrl1-param	uint8-array	Power Control 1 Parameter This property is required.
pvgam-param	uint8-array	Positive Voltage Gamma Control Parameter This property is required.
nvgam-param	uint8-array	Negative Voltage Gamma Control Parameter This property is required.
ram-param	uint8-array	RAM Control Parameter This property is required.
rgb-param	uint8-array	RGB Interface Control Parameter This property is required.
mipi-mode	string	MIPI DBI mode in use. These definitions should match those in dt-bindings/mipi_dbi/mipi_dbi.h This property is required. Legal values: 'MIPI_DBI_MODE_SPI_3WIRE', 'MIPI_DBI_MODE_SPI_4WIRE', 'MIPI_DBI_MODE_6800_BUS_16_BIT', 'MIPI_DBI_MODE_6800_BUS_9_BIT', 'MIPI_DBI_MODE_6800_BUS_8_BIT', 'MIPI_DBI_MODE_8080_BUS_16_BIT', 'MIPI_DBI_MODE_8080_BUS_9_BIT', 'MIPI_DBI_MODE_8080_BUS_8_BIT'
duplex	int	SPI Duplex mode, full or half. By default it's always full duplex thus 0 as this is, by far, the most common mode. Selecting half duplex allows to use SPI MOSI as a bidirectional line, typically used when only one data line is connected. Use the macros not the actual enum value, here is the concordance list (see dt-bindings/spi/spi.h) 0 SPI_FULL_DUPLEX 2048 SPI_HALF_DUPLEX
mipi-cpol	boolean	SPI clock polarity which indicates the clock idle state. If it is used, the clock idle state is logic high; otherwise, low.
mipi-cpha	boolean	SPI clock phase that indicates on which edge data is sampled. If it is used, data is sampled on the second edge; otherwise, on the first edge.
mipi-hold-cs	boolean	In some cases, it is necessary for the master to manage SPI chip select under software control, so that multiple spi transactions can be performed without releasing it. A typical use case is variable length SPI packets where the first spi transaction reads the length and the second spi transaction reads length bytes.
mipi-max-frequency	int	Maximum clock frequency of device's MIPI interface in Hz
supply-gpios	phandle-array	GPIO specifier that controls power to the device. This property should be provided when the device has a dedicated switch that controls power to the device. The supply state is entirely the responsibility of the device driver. Contrast with vin-supply.
vin-supply	phandle	Reference to the regulator that controls power to the device. The referenced devicetree node must have a regulator compatible. This property should be provided when device power is supplied by a shared regulator. The supply state is dependent on the request status of all devices fed by the regulator. Contrast with supply-gpios. If both properties are provided then the regulator must be requested before the supply GPIOS is set to an active state, and the supply GPIOS must be set to an inactive state before releasing the regulator.
height	int	Height of the panel driven by the controller, with the units in pixels. This property is required.
width	int	Width of the panel driven by the controller, with the units in pixels. This property is required.