microchip,eic-g1-intc
Description
Microchip External Interrupt Controller for g1 peripherals
Group g1 EIC supports following hardware peripherals:
- module name="EIC" id="U2254" version="3.0.0"
Properties
Properties not inherited from the base binding file.
Name |
Type |
Details |
|---|---|---|
|
|
Enables low power mode for eic peripheral
|
|
|
Each bit in the property denotes a pin number. This shows the pins which
do not support interrupt for port a.
|
|
|
Each bit in the property denotes a pin number. This shows the pins which
do not support interrupt for portb.
|
|
|
Each bit in the property denotes a pin number. This shows the pins which
do not support interrupt for portc.
|
|
|
Each bit in the property denotes a pin number. This shows the pins which
support interrupt in portd
|
|
|
Each bit in this number denotes a pin number. These pins are derived from datasheet
by listing down the eic line and port-pin mapping.
The eic line mapping to the pin number requires a manipulation with an offset.
Default value: |
|
|
Number of cells in portb-special-pins-1 property
Default value: |
|
|
Each bit in this number denotes a pin number. These pins are derived from datasheet
The eic line mapping to the pin number requires a manipulation with an offset.
Default value: |
|
|
Number of cells in portc-special-pins-1 property
Default value: |
|
|
Each bit in this number denotes a pin number. These pins are derived from datasheet
The eic line mapping to the pin number requires a manipulation with an offset.
Default value: |
|
|
Number of cells in portd-special-pins-1 property
Default value: |
|
|
Each bit in this number denotes a pin number. These pins are derived from datasheet
The eic line mapping to the pin number requires a manipulation with an offset.
Default value: |
|
|
Number of cells in portd-special-pins-2 property
Default value: |
Deprecated properties not inherited from the base binding file.
(None)
Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “microchip,eic-g1-intc” compatible.
Name |
Type |
Details |
|---|---|---|
|
|
Specifies the base address and size of the register
block of external interrupt controller.
This property is required. See Important properties for more information. |
|
|
Specifies the interrupt line in the NVIC
This property is required. See Important properties for more information. |
|
|
Indicates the operational status of the hardware or other
resource that the node represents. In particular:
- "okay" means the resource is operational and, for example,
can be used by device drivers
- "disabled" means the resource is not operational and the system
should treat it as if it is not present
For details, see "2.3.4 status" in Devicetree Specification v0.4.
Legal values: See Important properties for more information. |
|
|
This property is a list of strings that essentially define what
type of hardware or other resource this devicetree node
represents. Each device driver checks for specific compatible
property values to find the devicetree nodes that represent
resources that the driver should manage.
The recommended format is "vendor,device", The "vendor" part is
an abbreviated name of the vendor. The "device" is usually from
the datasheet.
The compatible property can have multiple values, ordered from
most- to least-specific. Having additional values is useful when the
device is a specific instance of a more general family, to allow the
system to match the most specific driver available.
For details, see "2.3.1 compatible" in Devicetree Specification v0.4.
This property is required. See Important properties for more information. |
|
|
Optional names given to each register block in the "reg" property.
For example:
/ {
soc {
#address-cells = <1>;
#size-cells = <1>;
uart@1000 {
reg = <0x1000 0x2000>, <0x3000 0x4000>;
reg-names = "foo", "bar";
};
};
};
The uart@1000 node has two register blocks:
- one with base address 0x1000, size 0x2000, and name "foo"
- another with base address 0x3000, size 0x4000, and name "bar"
|
|
|
Extended interrupt specifier for device, used as an alternative to
the "interrupts" property.
For details, see "2.4 Interrupts and Interrupt Mapping" in
Devicetree Specification v0.4.
|
|
|
Optional names given to each interrupt generated by a device.
The interrupts themselves are defined in either "interrupts" or
"interrupts-extended" properties.
For details, see "2.4 Interrupts and Interrupt Mapping" in
Devicetree Specification v0.4.
|
|
|
If present, this refers to the node which handles interrupts generated
by this device.
For details, see "2.4 Interrupts and Interrupt Mapping" in
Devicetree Specification v0.4.
|
|
|
Human readable string describing the device. Use of this property is
deprecated except as needed on a case-by-case basis.
For details, see "4.1.2 Miscellaneous Properties" in Devicetree
Specification v0.4.
See Important properties for more information. |
|
|
Information about the device's clock providers. In general, this property
should follow conventions established in the dt-schema binding:
https://github.com/devicetree-org/dt-schema/blob/main/dtschema/schemas/clock/clock.yaml
|
|
|
Optional names given to each clock provider in the "clocks" property.
|
|
|
This property encodes the number of <u32> cells used by address fields
in "reg" properties in this node's children.
For details, see "2.3.5 #address-cells and #size-cells" in Devicetree
Specification v0.4.
|
|
|
This property encodes the number of <u32> cells used by size fields in
"reg" properties in this node's children.
For details, see "2.3.5 #address-cells and #size-cells" in Devicetree
Specification v0.4.
|
|
|
DMA channel specifiers relevant to the device.
|
|
|
Optional names given to the DMA channel specifiers in the "dmas" property.
|
|
|
IO channel specifiers relevant to the device.
|
|
|
Optional names given to the IO channel specifiers in the "io-channels" property.
|
|
|
Mailbox / IPM channel specifiers relevant to the device.
|
|
|
Optional names given to the mbox specifiers in the "mboxes" property.
|
|
|
Power domain specifiers relevant to the device.
|
|
|
Optional names given to the power domain specifiers in the "power-domains" property.
|
|
|
Number of cells in power-domains property
|
|
|
HW spinlock id relevant to the device.
|
|
|
Optional names given to the hwlock specifiers in the "hwlocks" property.
|
|
|
Do not initialize device automatically on boot. Device should be manually
initialized using device_init().
|
|
|
Property to identify that a device can be used as wake up source.
When this property is provided a specific flag is set into the
device that tells the system that the device is capable of
wake up the system.
Wake up capable devices are disabled (interruptions will not wake up
the system) by default but they can be enabled at runtime if necessary.
|
|
|
Automatically configure the device for runtime power management after the
init function runs.
|
|
|
List of power states that will disable this device power.
|
Specifier cell names
portb-special-pins-1 cells: pins_val, offset
portc-special-pins-1 cells: pins_val, offset
portd-special-pins-1 cells: pins_val, offset
portd-special-pins-2 cells: pins_val, offset