swir,hl78xx-gnss (on uart bus)

Description

Binding for a modem child node that indicates the modem supports
GNSS functionality. This node is intended to be a child of a modem
device node (for example, `modem: hl_modem { ... };`).

The binding is intentionally small and extensible; it documents a
presence node (compatible = "swir,hl78xx-gnss") and may be extended
in future with additional properties that the driver may consume.

Examples

&uart0 {
        current-speed = <9600>;
        /* ... */
        gnss: gnss-nmea-generic {
                compatible = "gnss-nmea-generic";
        };
};

Properties

Properties not inherited from the base binding file.

Name	Type	Details
`fix-rate`	`int`	Initial fix-rate GNSS modem will be operating on. May be adjusted at run-time through GNSS APIs. Must be greater than 50-ms. Default is power-on setting. Default value: `1000`
`enable-gpios`	`phandle-array`	GPIO that enables the receiver when active and puts it into standby when inactive. The driver asserts this signal on resume and deasserts it on suspend.
`reset-gpios`	`phandle-array`	GPIO that resets the receiver when active. The driver pulses this signal during initialization. Requires reset-pulse-duration-ms.
`reset-pulse-duration-ms`	`int`	Minimum reset pulse duration in milliseconds.
`startup-time-ms`	`int`	Time in milliseconds for the receiver to start after asserting enable-gpios. The driver waits this long before communicating with the receiver. The default preserves operation without an enable signal. Set this to the receiver's wake-up time when enable-gpios is used. Default value: `0`
`pps-mode`	`string`	PPS output mode: - GNSS_PPS_MODE_DISABLED: Output disabled - GNSS_PPS_MODE_ENABLED: Output always enabled - GNSS_PPS_MODE_ENABLED_AFTER_LOCK: Output enabled from first lock - GNSS_PPS_MODE_ENABLED_WHILE_LOCKED: Output enabled only while locked This property is required. Legal values: `GNSS_PPS_MODE_DISABLED`, `GNSS_PPS_MODE_ENABLED`, `GNSS_PPS_MODE_ENABLED_AFTER_LOCK`, `GNSS_PPS_MODE_ENABLED_WHILE_LOCKED`
`pps-pulse-width`	`int`	1PPS pulse width Default value: `100`

Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “swir,hl78xx-gnss” compatible.

Name	Type	Details
`status`	`string`	Indicates the operational status of the hardware or other resource that the node represents. In particular: - "okay" means the resource is operational and, for example, can be used by device drivers - "disabled" means the resource is not operational and the system should treat it as if it is not present For details, see "2.3.4 status" in Devicetree Specification v0.4. Legal values: `okay`, `disabled`, `reserved`, `fail`, `fail-sss` See Important properties for more information.
`compatible`	`string-array`	This property is a list of strings that essentially define what type of hardware or other resource this devicetree node represents. Each device driver checks for specific compatible property values to find the devicetree nodes that represent resources that the driver should manage. The recommended format is "vendor,device", The "vendor" part is an abbreviated name of the vendor. The "device" is usually from the datasheet. The compatible property can have multiple values, ordered from most- to least-specific. Having additional values is useful when the device is a specific instance of a more general family, to allow the system to match the most specific driver available. For details, see "2.3.1 compatible" in Devicetree Specification v0.4. This property is required. See Important properties for more information.
`reg`	`array`	Information used to address the device. The value is specific to the device (i.e. is different depending on the compatible property). The "reg" property is typically a sequence of (address, length) pairs. Each pair is called a "register block". Values are conventionally written in hex. For details, see "2.3.6 reg" in Devicetree Specification v0.4. See Important properties for more information.
`reg-names`	`string-array`	Optional names given to each register block in the "reg" property. For example: / { soc { #address-cells = <1>; #size-cells = <1>; uart@1000 { reg = <0x1000 0x2000>, <0x3000 0x4000>; reg-names = "foo", "bar"; }; }; }; The uart@1000 node has two register blocks: - one with base address 0x1000, size 0x2000, and name "foo" - another with base address 0x3000, size 0x4000, and name "bar"
`ranges`	`compound`	Information used to define a mapping (or translation) between the address space of a bus (the "child address space") and the address space of the bus node's parent (the "parent address space"). The "ranges" property is typically empty, or a sequence of triplets (child bus address, parent bus address, length). If the "ranges" property is empty, it specifies that the parent and child address spaces are identical and no address translation is required. If the "ranges" property is not present in a bus node, it is assumed that no mapping exists between children of the node and the parent address space. For details, see "2.3.8 ranges" in Devicetree Specification v0.4.
`interrupts`	`array`	Information about interrupts generated by the device, encoded as an array of one or more interrupt specifiers. The format of the data in this property varies by where the device appears in the interrupt tree. Devices with the same "interrupt-parent" will use the same format in their interrupts properties. For details, see "2.4 Interrupts and Interrupt Mapping" in Devicetree Specification v0.4. See Important properties for more information.
`interrupts-extended`	`compound`	Extended interrupt specifier for device, used as an alternative to the "interrupts" property. For details, see "2.4 Interrupts and Interrupt Mapping" in Devicetree Specification v0.4.
`interrupt-names`	`string-array`	Optional names given to each interrupt generated by a device. The interrupts themselves are defined in either "interrupts" or "interrupts-extended" properties. For details, see "2.4 Interrupts and Interrupt Mapping" in Devicetree Specification v0.4.
`interrupt-parent`	`phandle`	If present, this refers to the node which handles interrupts generated by this device. For details, see "2.4 Interrupts and Interrupt Mapping" in Devicetree Specification v0.4.
`label`	`string`	Human readable string describing the device. Use of this property is deprecated except as needed on a case-by-case basis. For details, see "4.1.2 Miscellaneous Properties" in Devicetree Specification v0.4. See Important properties for more information.
`clocks`	`phandle-array`	Information about the device's clock providers. In general, this property should follow conventions established in the dt-schema binding: https://github.com/devicetree-org/dt-schema/blob/main/dtschema/schemas/clock/clock.yaml
`clock-names`	`string-array`	Optional names given to each clock provider in the "clocks" property.
`#address-cells`	`int`	This property encodes the number of <u32> cells used by address fields in "reg" properties in this node's children. For details, see "2.3.5 #address-cells and #size-cells" in Devicetree Specification v0.4.
`#size-cells`	`int`	This property encodes the number of <u32> cells used by size fields in "reg" properties in this node's children. For details, see "2.3.5 #address-cells and #size-cells" in Devicetree Specification v0.4.
`dma-coherent`	`boolean`	Indicates that the device is capable of coherent DMA operations. For details, see "2.3.10 dma-coherent" in Devicetree Specification v0.4.
`dmas`	`phandle-array`	DMA channel specifiers relevant to the device.
`dma-names`	`string-array`	Optional names given to the DMA channel specifiers in the "dmas" property.
`dma-ranges`	`compound`	The dma-ranges provides a means of defining a mapping or translation between the physical address space of the bus and the physical address space of the parent of the bus. For details, see "2.3.9 dma-ranges" in Devicetree Specification v0.4.
`io-channels`	`phandle-array`	IO channel specifiers relevant to the device.
`io-channel-names`	`string-array`	Optional names given to the IO channel specifiers in the "io-channels" property.
`mboxes`	`phandle-array`	Mailbox / IPM channel specifiers relevant to the device.
`mbox-names`	`string-array`	Optional names given to the mbox specifiers in the "mboxes" property.
`power-domains`	`phandle-array`	Power domain specifiers relevant to the device.
`power-domain-names`	`string-array`	Optional names given to the power domain specifiers in the "power-domains" property.
`#power-domain-cells`	`int`	Number of cells in power-domains property
`hwlocks`	`phandle-array`	HW spinlock id relevant to the device.
`hwlock-names`	`string-array`	Optional names given to the hwlock specifiers in the "hwlocks" property.
`zephyr,deferred-init`	`boolean`	Do not initialize device automatically on boot. Device should be manually initialized using device_init().
`wakeup-source`	`boolean`	Property to identify that a device can be used as wake up source. When this property is provided a specific flag is set into the device that tells the system that the device is capable of wake up the system. Wake up capable devices are disabled (interruptions will not wake up the system) by default but they can be enabled at runtime if necessary.
`zephyr,pm-device-runtime-auto`	`boolean`	Automatically configure the device for runtime power management after the init function runs.
`zephyr,disabling-power-states`	`phandles`	List of power states that will disable this device power.