ti,mspm0-opa

Description

Texas Instruments MSPM0 zero-drift, chopper-stabilized Operational Amplifier (OPA).

Properties

Properties not inherited from the base binding file.

Name

Type

Details

ti,psel

string

Selects non inverting terminals input via OPA's internal P-MUX.

Default value: open

Legal values: open, in0p, in1p, dac12out, dac8out, vref, prev-opa-rtop, gpamp-out, vss

ti,nsel

string

Selects inverting terminals input via OPA's internal N-MUX.

Default value: open

Legal values: open, in0n, in1n, prev-opa-rbot, rtap, rtop

ti,msel

string

Selects the input for OPA's internal M-MUX which is connected to the
programmable gain stage resister ladder.

Default value: open

Legal values: open, in1n, gnd, dac12out, prev-opa-rtop

ti,chop-mode

string

Selects the OPA's chopping mode.

Default value: disabled

Legal values: disabled, standard, adc-assisted

ti,outpin-enable

boolean

Enables the opa output on the external OPAx_OUT package pin.

ti,power-mode

string

Selects the opa power mode.
LP mode sets the GBW value as 1MHz,
STD mode sets the GBW value as 6MHz.

Default value: lp

Legal values: lp, std

ti,rri-enable

boolean

Selects rail-to-rail input mode.

vref

phandle

Selects vref as the input for non-inverting terminal.

functional-mode

string

Selects opamp functional mode.

a) differential mode

- Signals applied to both inputs
- Amplifies the difference between two input signals
- Common-mode signals are rejected
- Used in instrumentation and noise rejection
- Vout = (Rf/Rin) * (Vin2 - Vin1), where Rf is the feedback resistor
  and Rin is the input resistor, with gain (Rf/Rin)

         Rin        Rf
Vin1 --/\/\/\--*--/\/\/\-----
               |            |
               |     |\     |
               ------|- \   |
                     |   >--*-- Vout
               ------|+ /
               |     |/
               |
Vin2 --/\/\/\--*--/\/\/\-----
         Rin        Rf      |
                           GND

b) inverting mode

- Input signal applied to inverting (-) terminal
- Non-inverting (+) terminal connected to ground
- Feedback resistor connects output to inverting input
- Output is 180° out of phase with input
- Vout = (-Rf/Rin) * Vin, where Rf is the feedback resistor
  and Rin is the input resistor, s.t. gain is (-Rf/Rin)

        Rin        Rf
Vin --/\/\/\--*--/\/\/\-----
              |            |
              |     |\     |
              ------|- \   |
                    |   >--*-- Vout
              ------|+ /
              |     |/
            GND

c) non_inverting mode

- Input signal applied to non-inverting (+) terminal
- Inverting (-) terminal connected to feedback network
- Output is in phase with input
- Vout = (1 + (Rf/Rin)) * Vin, where Rf is the feedback resistor
  and Rin is the input resistor, s.t. gain is (1 + (Rf/Rin))

      Rin        Rf
 |--/\/\/\--*--/\/\/\-----
 |          |            |
GND         |     |\     |
            ------|- \   |
                  |   >--*-- Vout
        Vin ------|+ /
                  |/

d) follower mode (voltage follower or buffer)

- Special case of non-inverting amplifier
- Vout = 1 * Vin, s.t. gain is 1
- Direct feedback from output to inverting input
- Very high input impedance, very low output impedance
- Used for impedance matching

    --------------
    |            |
    |     |\     |
    ------|- \   |
          |   >--*-- Vout
Vin ------|+ /
          |/

e) standalone mode

- The opamp mode is defined by external circuitry

          |\
Vin- -----|- \
          |   >---- Vout
Vin+ -----|+ /
          |/

References:
  - https://www.electronics-tutorials.ws/category/opamp

This property is required.

Legal values: differential, inverting, non_inverting, follower, standalone

programmable-gain

string-array

If the OPAMP supports programmable gain, then the gain of
the opamp can be changed dynamically at runtime. The gain
value needs to be one of the enumerations above.
Gain selection:
- OPAMP_GAIN_1_7  : x 1/7
- OPAMP_GAIN_1_3  : x 1/3
- OPAMP_GAIN_1    : x 1
- OPAMP_GAIN_5_3  : x 5/3
- OPAMP_GAIN_2    : x 2
- OPAMP_GAIN_11_5 : x 11/5
- OPAMP_GAIN_3    : x 3
- OPAMP_GAIN_4    : x 4
- OPAMP_GAIN_13_3 : x 13/3
- OPAMP_GAIN_7    : x 7
- OPAMP_GAIN_8    : x 8
- OPAMP_GAIN_15   : x 15
- OPAMP_GAIN_16   : x 16
- OPAMP_GAIN_31   : x 31
- OPAMP_GAIN_32   : x 32
- OPAMP_GAIN_33   : x 33
- OPAMP_GAIN_63   : x 63
- OPAMP_GAIN_64   : x 64

Legal values: OPAMP_GAIN_1_7, OPAMP_GAIN_1_3, OPAMP_GAIN_1, OPAMP_GAIN_5_3, OPAMP_GAIN_2, OPAMP_GAIN_11_5, OPAMP_GAIN_3, OPAMP_GAIN_4, OPAMP_GAIN_13_3, OPAMP_GAIN_7, OPAMP_GAIN_8, OPAMP_GAIN_15, OPAMP_GAIN_16, OPAMP_GAIN_31, OPAMP_GAIN_32, OPAMP_GAIN_33, OPAMP_GAIN_63, OPAMP_GAIN_64

pinctrl-0

phandles

Pin configuration/s for the first state. Content is specific to the
selected pin controller driver implementation.

pinctrl-1

phandles

Pin configuration/s for the second state. See pinctrl-0.

pinctrl-2

phandles

Pin configuration/s for the third state. See pinctrl-0.

pinctrl-3

phandles

Pin configuration/s for the fourth state. See pinctrl-0.

pinctrl-4

phandles

Pin configuration/s for the fifth state. See pinctrl-0.

pinctrl-names

string-array

Names for the provided states. The number of names needs to match the
number of states.