ambiq,apollo4-pinctrl

Description

The Ambiq Apollo4 pin controller is a node responsible for controlling
pin function selection and pin properties, such as routing a UART0 TX
to pin 60 and enabling the pullup resistor on that pin.

The node has the 'pinctrl' node label set in your SoC's devicetree,
so you can modify it like this:

  &pinctrl {
          /* your modifications go here */
  };

All device pin configurations should be placed in child nodes of the
'pinctrl' node, as shown in this example:

  /* You can put this in places like a board-pinctrl.dtsi file in
   * your board directory, or a devicetree overlay in your application.
   */

  /* include pre-defined combinations for the SoC variant used by the board */
  #include <dt-bindings/pinctrl/ambiq-apollo4-pinctrl.h>

  &pinctrl {
    uart0_default: uart0_default {
      group1 {
        pinmux = <UART0TX_P60>;
      };
      group2 {
        pinmux = <UART0RX_P47>;
        input-enable;
      };
    };
  };

The 'uart0_default' child node encodes the pin configurations for a
particular state of a device; in this case, the default (that is, active)
state.

As shown, pin configurations are organized in groups within each child node.
Each group can specify a list of pin function selections in the 'pinmux'
property.

A group can also specify shared pin properties common to all the specified
pins, such as the 'input-enable' property in group 2.

Properties

Top level properties

These property descriptions apply to “ambiq,apollo4-pinctrl” nodes themselves. This page also describes child node properties in the following sections.

Properties not inherited from the base binding file.

(None)

Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “ambiq,apollo4-pinctrl” compatible.

Name	Type	Details
`status`	`string`	indicates the operational status of a device Legal values: `'ok'`, `'okay'`, `'disabled'`, `'reserved'`, `'fail'`, `'fail-sss'` See Important properties for more information.
`compatible`	`string-array`	compatible strings This property is required. See Important properties for more information.
`reg`	`array`	register space See Important properties for more information.
`reg-names`	`string-array`	name of each register space
`interrupts`	`array`	interrupts for device See Important properties for more information.
`interrupts-extended`	`compound`	extended interrupt specifier for device
`interrupt-names`	`string-array`	name of each interrupt
`interrupt-parent`	`phandle`	phandle to interrupt controller node
`label`	`string`	No description provided for this label See Important properties for more information.
`clocks`	`phandle-array`	Clock gate information
`clock-names`	`string-array`	name of each clock
`#address-cells`	`int`	number of address cells in reg property
`#size-cells`	`int`	number of size cells in reg property
`dmas`	`phandle-array`	DMA channels specifiers
`dma-names`	`string-array`	Provided names of DMA channel specifiers
`io-channels`	`phandle-array`	IO channels specifiers
`io-channel-names`	`string-array`	Provided names of IO channel specifiers
`mboxes`	`phandle-array`	mailbox / IPM channels specifiers
`mbox-names`	`string-array`	Provided names of mailbox / IPM channel specifiers
`power-domains`	`phandle-array`	Power domain specifiers
`power-domain-names`	`string-array`	Provided names of power domain specifiers
`#power-domain-cells`	`int`	Number of cells in power-domains property
`zephyr,deferred-init`	`boolean`	Do not initialize device automatically on boot. Device should be manually initialized using device_init().
`wakeup-source`	`boolean`	Property to identify that a device can be used as wake up source. When this property is provided a specific flag is set into the device that tells the system that the device is capable of wake up the system. Wake up capable devices are disabled (interruptions will not wake up the system) by default but they can be enabled at runtime if necessary.
`zephyr,pm-device-runtime-auto`	`boolean`	Automatically configure the device for runtime power management after the init function runs.
`zephyr,disabling-power-states`	`phandles`	List of power states that will disable this device power.

Grandchild node properties

Name	Type	Details
`pinmux`	`array`	An array of pins sharing the same group properties. Each element of the array is an integer constructed from the pin number and the alternative function of the pin. This property is required.
`drive-strength`	`string`	The drive strength of a pin, relative to full-driver strength. The default value is 0.1, which is the reset value. Default value: `0.1` Legal values: `'0.1'`, `'0.5'`, `'0.75'`, `'1.0'`
`slew-rate`	`string`	Select slew rate for a pin. The default is slow, which is the reset value. Default value: `slow` Legal values: `'slow'`, `'fast'`
`ambiq,pull-up-ohms`	`int`	The pullup resistor value. The default value is 1500 ohms. Default value: `1500` Legal values: `1500`, `6000`, `12000`, `24000`, `50000`, `100000`
`ambiq,iom-nce-module`	`int`	IOM nCE module select, selects the SPI channel (CE) number (0-42). 0, IOM0CE0 : IOM 0 NCE 0 module 1, IOM0CE1 : IOM 0 NCE 1 module 2, IOM0CE2 : IOM 0 NCE 2 module 3, IOM0CE3 : IOM 0 NCE 3 module 4, IOM1CE0 : IOM 1 NCE 0 module 5, IOM1CE1 : IOM 1 NCE 1 module 6, IOM1CE2 : IOM 1 NCE 2 module 7, IOM1CE3 : IOM 1 NCE 3 module 8, IOM2CE0 : IOM 2 NCE 0 module 9, IOM2CE1 : IOM 2 NCE 1 module 10, IOM2CE2 : IOM 2 NCE 2 module 11, IOM2CE3 : IOM 2 NCE 3 module 12, IOM3CE0 : IOM 3 NCE 0 module 13, IOM3CE1 : IOM 3 NCE 1 module 14, IOM3CE2 : IOM 3 NCE 2 module 15, IOM3CE3 : IOM 3 NCE 3 module 16, IOM4CE0 : IOM 4 NCE 0 module 17, IOM4CE1 : IOM 4 NCE 1 module 18, IOM4CE2 : IOM 4 NCE 2 module 19, IOM4CE3 : IOM 4 NCE 3 module 20, IOM5CE0 : IOM 5 NCE 0 module 21, IOM5CE1 : IOM 5 NCE 1 module 22, IOM5CE2 : IOM 5 NCE 2 module 23, IOM5CE3 : IOM 5 NCE 3 module 24, IOM6CE0 : IOM 6 NCE 0 module 25, IOM6CE1 : IOM 6 NCE 1 module 26, IOM6CE2 : IOM 6 NCE 2 module 27, IOM6CE3 : IOM 6 NCE 3 module 28, IOM7CE0 : IOM 7 NCE 0 module 29, IOM7CE1 : IOM 7 NCE 1 module 30, IOM7CE2 : IOM 7 NCE 2 module 31, IOM7CE3 : IOM 7 NCE 3 module 32, MSPI0CEN0 : MSPI 0 NCE 0 module 33, MSPI0CEN1 : MSPI 0 NCE 1 module 34, MSPI1CEN0 : MSPI 1 NCE 0 module 35, MSPI1CEN1 : MSPI 1 NCE 1 module 36, MSPI2CEN0 : MSPI 2 NCE 0 module 37, MSPI2CEN1 : MSPI 2 NCE 1 module 38, DC_DPI_DE : DC DPI DE module 39, DISP_CONT_CSX : DISP CONT CSX module 40, DC_SPI_CS_N : DC SPI CS_N module 41, DC_QSPI_CS_N : DC QSPI CS_N module 42, DC_RESX : DC module RESX If the pin is not a CE, this descriptor will be ignored. Default value 0, which is the reset value.
`ambiq,iom-mspi`	`int`	Indicates the module which uses specific CE pin, 1 if CE is IOM, 0 if MSPI. Default value 0, which is the reset value. If the pin is not a CE, this descriptor will be ignored.
`ambiq,iom-num`	`int`	Indicates the instance which uses specific CE pin. IOM number (0-7) or MSPI (0-2). Default value 0, which is the reset value. If the pin is not a CE, this descriptor will be ignored.
`ambiq,interrupt-direction`	`int`	Indicates the pininterrupt direction. Default value 0, which is the reset value.
`bias-high-impedance`	`boolean`	high impedance mode ("third-state", "floating")
`bias-pull-up`	`boolean`	enable pull-up resistor
`bias-pull-down`	`boolean`	enable pull-down resistor
`drive-push-pull`	`boolean`	drive actively high and low
`drive-open-drain`	`boolean`	drive with open drain (hardware AND)
`input-enable`	`boolean`	enable input on pin (e.g. enable an input buffer, no effect on output)