microchip,mec5-pinctrl

Vendor: Microchip Technology Inc.

Note

An implementation of a driver matching this compatible is available in drivers/pinctrl/pinctrl_mchp_mec5.c.

Description

Microchip XEC Pin controller Node
Based on pincfg-node.yaml binding.
The MCHP XEC pin controller is a singleton node responsible for controlling
pin function selection and pin properties. For example, you can use this
node to select peripheral pin functions.

The node has the 'pinctrl' node label set in your SoC's devicetree,
so you can modify it like this:

  &pinctrl {
          /* your modifications go here */
  };

All device pin configurations should be placed in child nodes of the
'pinctrl' node, as in the spi0 example shown at the end:

A group can also specify shared pin properties common to all the specified
pins, such as the 'bias-pull-up' property in group 2. Here is a list of
supported standard pin properties:

- bias-disable: Disable pull-up/down (default behavior, not required).
- bias-pull-down: Enable pull-down resistor.
- bias-pull-up: Enable pull-up resistor.
- drive-push-pull: Output driver is push-pull (default, not required).
- drive-open-drain: Output driver is open-drain.
- output-high: Set output state high when pin configured.
- output-low: Set output state low when pin configured.

Custom pin properties for drive strength and slew rate are available:
- drive-strength
- slew-rate

Driver strength and slew rate hardware defaults vary by SoC and pin.

An example for MEC174x family, include the chip level pinctrl
DTSI file in the board level DTS:

  #include <microchip/mec5/mec1743qlj-a0-pinctrl.dtsi>

We want to use the shared SPI port of the MEC172x QMSPI controller
and want the chip select 0 to be open-drain.

To change a pin's pinctrl default properties add a reference to the
pin in the board's DTS file and set the properties.

  &spi0 {
    pinctrl-0 = < &shd_cs0_n_gpio055
                  &shd_clk_gpio056
                  &shd_io0_gpio223
                  &shd_io1_gpio224
                  &shd_io3_gpio016 >;
    pinctrl-names = "default";
  }

  &shd_cs0_n_gpio055 {
    drive-open-drain;
  };

Properties

Top level properties

These property descriptions apply to “microchip,mec5-pinctrl” nodes themselves. This page also describes child node properties in the following sections.

Node specific propertiesDeprecated node specific propertiesBase properties

Properties not inherited from the base binding file.

(None)

Child node properties

Name	Type	Details
pinmux	int	Pinmux selection This property is required.
slew-rate	string	Pin speed. The default value of slew-rate is the SoC power-on-reset value. Please refer to the data sheet as a small number of pins may have a different default and some pins do not implement slew rate adjustment. Legal values: 'low-speed', 'high-speed'
drive-strength	string	Pin output drive strength for PIO and PIO-24 pin types. Default is "1x" for most pins. PIO pins are 2, 4, 8, or 12 mA. PIO-24 pins are 4, 8, 16, or 24 mA. Please refer to the data sheet for each pin's PIO type and default drive strength. Legal values: '1x', '2x', '4x', '6x'
microchip,output-func-invert	boolean	Invert polarity of an output alternate function. Input functions are not affected.
bias-disable	boolean	disable any pin bias
bias-pull-up	boolean	enable pull-up resistor
bias-pull-down	boolean	enable pull-down resistor
drive-push-pull	boolean	drive actively high and low
drive-open-drain	boolean	drive with open drain (hardware AND)
low-power-enable	boolean	enable low power mode
output-disable	boolean	disable output on a pin (e.g. disable an output buffer)
output-enable	boolean	enable output on a pin without actively driving it (e.g. enable an output buffer)
output-low	boolean	set the pin to output mode with low level
output-high	boolean	set the pin to output mode with high level