espressif,esp32-sdhc-slot

Note

An implementation of a driver matching this compatible is available in drivers/sdhc/sdhc_esp32.c.

Description

These nodes are “sd” bus nodes.

Espressif ESP32 SDHC controller slot

Properties

Properties not inherited from the base binding file.

Name	Type	Details
`pinctrl-0`	`phandles`	Pin configuration/s for the first state. Content is specific to the selected pin controller driver implementation. This property is required.
`pinctrl-names`	`string-array`	Names for the provided states. The number of names needs to match the number of states. This property is required.
`bus-width`	`int`	SD bus width in bits Default value: `4` Legal values: `1`, `4`
`clk-pin`	`int`	Clock pin for ESP32 and SoC models with fixed pins for SDIO. For devices with GPIO matrix support, configuration shall be done using pin control (pinctrl-0 field).
`cmd-pin`	`int`	Command pin for ESP32 and SoC models with fixed pins for SDIO. For devices with GPIO matrix support, configuration shall be done using pin control (pinctrl-0 field).
`d0-pin`	`int`	Data 0 pin for ESP32 and SoC models with fixed pins for SDIO. For devices with GPIO matrix support, configuration shall be done using pin control (pinctrl-0 field).
`d1-pin`	`int`	Data 1 pin for ESP32 and SoC models with fixed pins for SDIO. For devices with GPIO matrix support, configuration shall be done using pin control (pinctrl-0 field).
`d2-pin`	`int`	Data 2 pin for ESP32 and SoC models with fixed pins for SDIO. For devices with GPIO matrix support, configuration shall be done using pin control (pinctrl-0 field).
`d3-pin`	`int`	Data 3 pin for ESP32 and SoC models with fixed pins for SDIO. For devices with GPIO matrix support, configuration shall be done using pin control (pinctrl-0 field).
`pwr-gpios`	`phandle-array`	Power pin This is a configurable pin to deliver power supply to the SD card. It is configured as a GPIO in order to execute power toggles and reinitialize the SD slave when necessary.
`max-current-330`	`int`	Max drive current in mA at 3.3V. A value of zero indicates no maximum is specified by the driver.
`max-current-300`	`int`	Max drive current in mA at 3.0V. A value of zero indicates no maximum is specified by the driver.
`max-current-180`	`int`	Max drive current in mA at 1.8V. A value of zero indicates no maximum is specified by the driver.
`max-bus-freq`	`int`	Maximum bus frequency for SD card. This should be the highest frequency the SDHC is capable of negotiating with cards on the bus. Default value: `400000`
`min-bus-freq`	`int`	Minimum bus frequency for SD card. This should be the frequency that cards first will select when attached to the SDHC bus Default value: `400000`
`power-delay-ms`	`int`	time in ms for SDHC to delay when toggling power to the SD card. This delay gives the card time to power up or down fully Default value: `500`
`mmc-hs200-1_8v`	`boolean`	The host controller supports HS200 at 1.8V
`mmc-hs400-1_8v`	`boolean`	The host controller supports HS400 at 1.8V
`pinctrl-1`	`phandles`	Pin configuration/s for the second state. See pinctrl-0.
`pinctrl-2`	`phandles`	Pin configuration/s for the third state. See pinctrl-0.
`pinctrl-3`	`phandles`	Pin configuration/s for the fourth state. See pinctrl-0.
`pinctrl-4`	`phandles`	Pin configuration/s for the fifth state. See pinctrl-0.

Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “espressif,esp32-sdhc-slot” compatible.

Name	Type	Details
`reg`	`array`	register space This property is required. See Important properties for more information.
`status`	`string`	indicates the operational status of a device Legal values: `'ok'`, `'okay'`, `'disabled'`, `'reserved'`, `'fail'`, `'fail-sss'` See Important properties for more information.
`compatible`	`string-array`	compatible strings This property is required. See Important properties for more information.
`reg-names`	`string-array`	name of each register space
`interrupts`	`array`	interrupts for device See Important properties for more information.
`interrupts-extended`	`compound`	extended interrupt specifier for device
`interrupt-names`	`string-array`	name of each interrupt
`interrupt-parent`	`phandle`	phandle to interrupt controller node
`label`	`string`	No description provided for this label See Important properties for more information.
`clocks`	`phandle-array`	Clock gate information
`clock-names`	`string-array`	name of each clock
`#address-cells`	`int`	number of address cells in reg property
`#size-cells`	`int`	number of size cells in reg property
`dmas`	`phandle-array`	DMA channels specifiers
`dma-names`	`string-array`	Provided names of DMA channel specifiers
`io-channels`	`phandle-array`	IO channels specifiers
`io-channel-names`	`string-array`	Provided names of IO channel specifiers
`mboxes`	`phandle-array`	mailbox / IPM channels specifiers
`mbox-names`	`string-array`	Provided names of mailbox / IPM channel specifiers
`power-domains`	`phandle-array`	Power domain specifiers
`power-domain-names`	`string-array`	Provided names of power domain specifiers
`#power-domain-cells`	`int`	Number of cells in power-domains property
`zephyr,deferred-init`	`boolean`	Do not initialize device automatically on boot. Device should be manually initialized using device_init().
`wakeup-source`	`boolean`	Property to identify that a device can be used as wake up source. When this property is provided a specific flag is set into the device that tells the system that the device is capable of wake up the system. Wake up capable devices are disabled (interruptions will not wake up the system) by default but they can be enabled at runtime if necessary.
`zephyr,pm-device-runtime-auto`	`boolean`	Automatically configure the device for runtime power management after the init function runs.
`zephyr,disabling-power-states`	`phandles`	List of power states that will disable this device power.