nxp,imx-usdhc

Note

An implementation of a driver matching this compatible is available in drivers/sdhc/imx_usdhc.c.

Description

These nodes are “sd” bus nodes.

NXP imx USDHC controller

Properties

Properties not inherited from the base binding file.

Name	Type	Details
`data-timeout`	`int`	Data timeout, as multiple of the SD clock. See DTOCV field of USDHC Default value: `15`
`read-watermark`	`int`	Number of words used as read watermark level in FIFO queue for USDHC Default value: `128`
`write-watermark`	`int`	Number of words used as write watermark level in FIFO queue for USDHC Default value: `128`
`max_current_330`	`int`	Max drive current in mA at 3.3V. A value of zero indicates no maximum is specified by the driver.
`pwr-gpios`	`phandle-array`	Power pin This pin defaults to active high when consumed by the SD card. The property value should ensure the flags properly describe the signal that is presented to the driver.
`cd-gpios`	`phandle-array`	Detect pin This pin defaults to active low when produced by the SD card. The property value should ensure the flags properly describe the signal that is presented to the driver.
`no-1-8-v`	`boolean`	When the external SD card circuit does not support 1.8V, add this property to disable 1.8v card voltage of SD card controller.
`detect-dat3`	`boolean`	Enable the host to detect an SD card via the DAT3 line of the SD card connection. Requires the board to define a function to pull DAT3 low or high using pullup/pulldown resistors.
`detect-cd`	`boolean`	Use the host's internal card detect signal (USDHC_CD) to detect the SD card. This signal is available as an alternative to card detect via GPIO, and should be connected to the SD slot's detect pin if used.
`max-current-330`	`int`	Max drive current in mA at 3.3V. A value of zero indicates no maximum is specified by the driver.
`max-current-300`	`int`	Max drive current in mA at 3.0V. A value of zero indicates no maximum is specified by the driver.
`max-current-180`	`int`	Max drive current in mA at 1.8V. A value of zero indicates no maximum is specified by the driver.
`max-bus-freq`	`int`	Maximum bus frequency for SD card. This should be the highest frequency the SDHC is capable of negotiating with cards on the bus. Default value: `400000`
`min-bus-freq`	`int`	Minimum bus frequency for SD card. This should be the frequency that cards first will select when attached to the SDHC bus Default value: `400000`
`power-delay-ms`	`int`	time in ms for SDHC to delay when toggling power to the SD card. This delay gives the card time to power up or down fully Default value: `500`
`mmc-hs200-1_8v`	`boolean`	The host controller supports HS200 at 1.8V
`mmc-hs400-1_8v`	`boolean`	The host controller supports HS400 at 1.8V
`pinctrl-0`	`phandles`	Pin configuration/s for the first state. Content is specific to the selected pin controller driver implementation.
`pinctrl-1`	`phandles`	Pin configuration/s for the second state. See pinctrl-0.
`pinctrl-2`	`phandles`	Pin configuration/s for the third state. See pinctrl-0.
`pinctrl-3`	`phandles`	Pin configuration/s for the fourth state. See pinctrl-0.
`pinctrl-4`	`phandles`	Pin configuration/s for the fifth state. See pinctrl-0.
`pinctrl-names`	`string-array`	Names for the provided states. The number of names needs to match the number of states.

Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “nxp,imx-usdhc” compatible.

Name	Type	Details
`reg`	`array`	register space This property is required. See Important properties for more information.
`clocks`	`phandle-array`	Clock gate information This property is required.
`status`	`string`	indicates the operational status of a device Legal values: `'ok'`, `'okay'`, `'disabled'`, `'reserved'`, `'fail'`, `'fail-sss'` See Important properties for more information.
`compatible`	`string-array`	compatible strings This property is required. See Important properties for more information.
`reg-names`	`string-array`	name of each register space
`interrupts`	`array`	interrupts for device See Important properties for more information.
`interrupts-extended`	`compound`	extended interrupt specifier for device
`interrupt-names`	`string-array`	name of each interrupt
`interrupt-parent`	`phandle`	phandle to interrupt controller node
`label`	`string`	No description provided for this label See Important properties for more information.
`clock-names`	`string-array`	name of each clock
`#address-cells`	`int`	number of address cells in reg property
`#size-cells`	`int`	number of size cells in reg property
`dmas`	`phandle-array`	DMA channels specifiers
`dma-names`	`string-array`	Provided names of DMA channel specifiers
`io-channels`	`phandle-array`	IO channels specifiers
`io-channel-names`	`string-array`	Provided names of IO channel specifiers
`mboxes`	`phandle-array`	mailbox / IPM channels specifiers
`mbox-names`	`string-array`	Provided names of mailbox / IPM channel specifiers
`power-domains`	`phandle-array`	Power domain specifiers
`power-domain-names`	`string-array`	Provided names of power domain specifiers
`#power-domain-cells`	`int`	Number of cells in power-domains property
`zephyr,deferred-init`	`boolean`	Do not initialize device automatically on boot. Device should be manually initialized using device_init().
`wakeup-source`	`boolean`	Property to identify that a device can be used as wake up source. When this property is provided a specific flag is set into the device that tells the system that the device is capable of wake up the system. Wake up capable devices are disabled (interruptions will not wake up the system) by default but they can be enabled at runtime if necessary.
`zephyr,pm-device-runtime-auto`	`boolean`	Automatically configure the device for runtime power management after the init function runs.
`zephyr,disabling-power-states`	`phandles`	List of power states that will disable this device power.