nuvoton,numaker-tcpc

Note

An implementation of a driver matching this compatible is available in drivers/usb_c/tcpc/ucpd_numaker.c.

Description

Nuvoton NuMaker USB Type-C port controller

Properties

Properties not inherited from the base binding file.

Name	Type	Details
`resets`	`phandle-array`	Reset information This property is required.
`vconn-overcurrent-event-polarity`	`string`	Polarity of VCONN overcurrent event Legal values: `'low-active'`, `'high-active'`
`vconn-discharge-polarity`	`string`	Polarity of VCONN discharge Legal values: `'low-active'`, `'high-active'`
`vconn-enable-polarity`	`string`	Polarity of VCONN enable Legal values: `'low-active'`, `'high-active'`
`vbus-overcurrent-event-polarity`	`string`	Polarity of VBUS overcurrent event Legal values: `'low-active'`, `'high-active'`
`vbus-forceoff-event-polarity`	`string`	Polarity of VBUS force-off event Legal values: `'low-active'`, `'high-active'`
`frs-tx-polarity`	`string`	Polarity of fast role swap tx Legal values: `'low-active'`, `'high-active'`
`vbus-discharge-enable-polarity`	`string`	Polarity of VBUS discharge enable Legal values: `'low-active'`, `'high-active'`
`vbus-sink-enable-polarity`	`string`	Polarity of VBUS sink enable Legal values: `'low-active'`, `'high-active'`
`vbus-source-enable-polarity`	`string`	Polarity of VBUS source enable Legal values: `'low-active'`, `'high-active'`
`vbus-divide`	`string`	VBUS measurement divider This property is required. Legal values: `'no-divide'`, `'divide-10'`, `'divide-20'`
`dead-battery`	`boolean`	Determine if USB-C Dead Battery pull-down resistor should be applied to the CC lines.
`pinctrl-0`	`phandles`	Pin configuration/s for the first state. Content is specific to the selected pin controller driver implementation. This property is required.
`pinctrl-names`	`string-array`	Names for the provided states. The number of names needs to match the number of states. This property is required.
`gpios`	`phandle-array`	This property is required.
`gpio-names`	`string-array`	Valid names of GPIO: "vbus-detect": GPIO for VBUS detect (must) "vbus-discharge": GPIO for VBUS discharge (option) "vconn-discharge": GPIO for VCONN discharge (option) This property is required.
`adc-measure-timer-trigger-rate`	`int`	Rate of timer-triggered EADC measurement (Hz). This is ignored when none of above is specified. The default is chosen by following BSP sample, and is to update UTCPD in a proper rate. Default value: `100`
`reset-names`	`string-array`	Name of each reset
`pinctrl-1`	`phandles`	Pin configuration/s for the second state. See pinctrl-0.
`pinctrl-2`	`phandles`	Pin configuration/s for the third state. See pinctrl-0.
`pinctrl-3`	`phandles`	Pin configuration/s for the fourth state. See pinctrl-0.
`pinctrl-4`	`phandles`	Pin configuration/s for the fifth state. See pinctrl-0.

Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “nuvoton,numaker-tcpc” compatible.

Name	Type	Details
`reg`	`array`	register space This property is required. See Important properties for more information.
`interrupts`	`array`	interrupts for device This property is required. See Important properties for more information.
`clocks`	`phandle-array`	Clock gate information This property is required.
`io-channels`	`phandle-array`	EADC channels for measuring VBUS/VCONN voltage
`io-channel-names`	`string-array`	Valid names of EADC channels: "chn-vbus": EADC channel for measuring VBUS voltage (option) "chn-vconn": EADC channel for measuring VCONN voltage (option)
`status`	`string`	indicates the operational status of a device Legal values: `'ok'`, `'okay'`, `'disabled'`, `'reserved'`, `'fail'`, `'fail-sss'` See Important properties for more information.
`compatible`	`string-array`	compatible strings This property is required. See Important properties for more information.
`reg-names`	`string-array`	name of each register space
`interrupts-extended`	`compound`	extended interrupt specifier for device
`interrupt-names`	`string-array`	name of each interrupt
`interrupt-parent`	`phandle`	phandle to interrupt controller node
`label`	`string`	Human readable string describing the device (used as device_get_binding() argument) See Important properties for more information. This property is deprecated.
`clock-names`	`string-array`	name of each clock
`#address-cells`	`int`	number of address cells in reg property
`#size-cells`	`int`	number of size cells in reg property
`dmas`	`phandle-array`	DMA channels specifiers
`dma-names`	`string-array`	Provided names of DMA channel specifiers
`mboxes`	`phandle-array`	mailbox / IPM channels specifiers
`mbox-names`	`string-array`	Provided names of mailbox / IPM channel specifiers
`power-domains`	`phandle-array`	Power domain specifiers
`power-domain-names`	`string-array`	Provided names of power domain specifiers
`#power-domain-cells`	`int`	Number of cells in power-domains property
`zephyr,deferred-init`	`boolean`	Do not initialize device automatically on boot. Device should be manually initialized using device_init().
`wakeup-source`	`boolean`	Property to identify that a device can be used as wake up source. When this property is provided a specific flag is set into the device that tells the system that the device is capable of wake up the system. Wake up capable devices are disabled (interruptions will not wake up the system) by default but they can be enabled at runtime if necessary.
`zephyr,pm-device-runtime-auto`	`boolean`	Automatically configure the device for runtime power management after the init function runs.
`zephyr,disabling-power-states`	`phandles`	List of power states that will disable this device power.