nordic,nrf-usbhs-phy-type2

Description

Nordic USBHS Type 2 PHY configuration

Properties

Properties not inherited from the base binding file.

Name	Type	Details
`compdistune`	`string`	Disconnect Threshold Adjustment. Adjusts the voltage level for the threshold used to detect a disconnect event at the host. Default value: `0` Legal values: `-4.65%`, `-3.29%`, `-1.44%`, `0`, `+1.85%`, `+3.40%`, `+5.48%`, `+7.15%`
`sqrxtune`	`string`	Squelch Threshold Adjustment. Adjusts the voltage level for the threshold used to detect valid high-speed data. Default value: `0` Legal values: `+16.75%`, `+11.06%`, `+5.66%`, `0`, `-5.42%`, `-11.03%`, `-16.35%`, `-21.90%`
`vdatreftune`	`string`	Data Detect Voltage Adjustment. Adjusts the threshold voltage level (Vdat_ref) used to detect data during Battery Charging 1.2 port detection. Default value: `0` Legal values: `+11.36%`, `0`, `-11.33%`, `-22.74%`
`txhsxvtune`	`string`	Transmitter High-Speed Crossover Adjustment. Adjusts the voltage at which the DP0 and DM0 signals cross while transmitting in HS mode. Default value: `0` Legal values: `-13 mV`, `+13 mV`, `0`
`txfslstune`	`string`	FS/LS Source Impedance Adjustment. Adjusts the low- and full-speed single-ended source impedance while driving high. Default value: `0` Legal values: `+15%`, `+7%`, `0`, `-6%`, `-12%`
`txvreftune`	`string`	HS DC Voltage Level Adjustment. Adjusts the high-speed DC level voltage. Default value: `0` Legal values: `-9%`, `-6%`, `-3%`, `0`, `+3%`, `+6%`, `+9%`, `+12%`, `+15%`, `+18%`, `+22%`, `+25%`, `+28%`, `+31%`, `+34%`, `+37%`
`txrisetune`	`string`	HS Transmitter Rise/Fall Time Adjustment. Adjusts the rise/fall times of the high-speed waveform. Default value: `0` Legal values: `+10%`, `0`, `-12%`, `-25%`
`txrestune`	`string`	USB Source Impedance Adjustment. Adjusts the driver source impedance to compensate for added series resistance on the USB. Default value: `0` Legal values: `+6.5 ohm`, `+3 ohm`, `0`, `-2 ohm`
`txpreempamptune`	`string`	HS Transmitter Pre-Emphasis Current Control. Controls the amount of current sourced to DP0 and DM0 after a J-to-K or K-to-J transition. The HS Transmitter pre-emphasis current is defined in terms of unit amounts. One unit amount is approximately 4 mA and is defined as 1x pre-emphasis current. Default value: `disabled` Legal values: `disabled`, `2x`, `1x`, `3x`
`txpreemppulsetune`	`string`	HS Transmitter Pre-Emphasis Duration Control. Controls the duration for which the HS pre-emphasis current is sourced onto DP0 or DM0. The HS Transmitter pre-emphasis duration is defined in terms of unit amounts. One unit of pre-emphasis duration is approximately 580 ps and is defined as 1x pre-emphasis duration. Default value: `2x` Legal values: `2x`, `1x`

Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “nordic,nrf-usbhs-phy-type2” compatible.

Name	Type	Details
`status`	`string`	Indicates the operational status of the hardware or other resource that the node represents. In particular: - "okay" means the resource is operational and, for example, can be used by device drivers - "disabled" means the resource is not operational and the system should treat it as if it is not present For details, see "2.3.4 status" in Devicetree Specification v0.4. Legal values: `okay`, `disabled`, `reserved`, `fail`, `fail-sss` See Important properties for more information.
`compatible`	`string-array`	This property is a list of strings that essentially define what type of hardware or other resource this devicetree node represents. Each device driver checks for specific compatible property values to find the devicetree nodes that represent resources that the driver should manage. The recommended format is "vendor,device", The "vendor" part is an abbreviated name of the vendor. The "device" is usually from the datasheet. The compatible property can have multiple values, ordered from most- to least-specific. Having additional values is useful when the device is a specific instance of a more general family, to allow the system to match the most specific driver available. For details, see "2.3.1 compatible" in Devicetree Specification v0.4. This property is required. See Important properties for more information.
`reg`	`array`	Information used to address the device. The value is specific to the device (i.e. is different depending on the compatible property). The "reg" property is typically a sequence of (address, length) pairs. Each pair is called a "register block". Values are conventionally written in hex. For details, see "2.3.6 reg" in Devicetree Specification v0.4. See Important properties for more information.
`reg-names`	`string-array`	Optional names given to each register block in the "reg" property. For example: / { soc { #address-cells = <1>; #size-cells = <1>; uart@1000 { reg = <0x1000 0x2000>, <0x3000 0x4000>; reg-names = "foo", "bar"; }; }; }; The uart@1000 node has two register blocks: - one with base address 0x1000, size 0x2000, and name "foo" - another with base address 0x3000, size 0x4000, and name "bar"
`ranges`	`compound`	Information used to define a mapping (or translation) between the address space of a bus (the "child address space") and the address space of the bus node's parent (the "parent address space"). The "ranges" property is typically empty, or a sequence of triplets (child bus address, parent bus address, length). If the "ranges" property is empty, it specifies that the parent and child address spaces are identical and no address translation is required. If the "ranges" property is not present in a bus node, it is assumed that no mapping exists between children of the node and the parent address space. For details, see "2.3.8 ranges" in Devicetree Specification v0.4.
`interrupts`	`array`	Information about interrupts generated by the device, encoded as an array of one or more interrupt specifiers. The format of the data in this property varies by where the device appears in the interrupt tree. Devices with the same "interrupt-parent" will use the same format in their interrupts properties. For details, see "2.4 Interrupts and Interrupt Mapping" in Devicetree Specification v0.4. See Important properties for more information.
`interrupts-extended`	`compound`	Extended interrupt specifier for device, used as an alternative to the "interrupts" property. For details, see "2.4 Interrupts and Interrupt Mapping" in Devicetree Specification v0.4.
`interrupt-names`	`string-array`	Optional names given to each interrupt generated by a device. The interrupts themselves are defined in either "interrupts" or "interrupts-extended" properties. For details, see "2.4 Interrupts and Interrupt Mapping" in Devicetree Specification v0.4.
`interrupt-parent`	`phandle`	If present, this refers to the node which handles interrupts generated by this device. For details, see "2.4 Interrupts and Interrupt Mapping" in Devicetree Specification v0.4.
`label`	`string`	Human readable string describing the device. Use of this property is deprecated except as needed on a case-by-case basis. For details, see "4.1.2 Miscellaneous Properties" in Devicetree Specification v0.4. See Important properties for more information.
`clocks`	`phandle-array`	Information about the device's clock providers. In general, this property should follow conventions established in the dt-schema binding: https://github.com/devicetree-org/dt-schema/blob/main/dtschema/schemas/clock/clock.yaml
`clock-names`	`string-array`	Optional names given to each clock provider in the "clocks" property.
`#address-cells`	`int`	This property encodes the number of <u32> cells used by address fields in "reg" properties in this node's children. For details, see "2.3.5 #address-cells and #size-cells" in Devicetree Specification v0.4.
`#size-cells`	`int`	This property encodes the number of <u32> cells used by size fields in "reg" properties in this node's children. For details, see "2.3.5 #address-cells and #size-cells" in Devicetree Specification v0.4.
`dma-coherent`	`boolean`	Indicates that the device is capable of coherent DMA operations. For details, see "2.3.10 dma-coherent" in Devicetree Specification v0.4.
`dmas`	`phandle-array`	DMA channel specifiers relevant to the device.
`dma-names`	`string-array`	Optional names given to the DMA channel specifiers in the "dmas" property.
`dma-ranges`	`compound`	The dma-ranges provides a means of defining a mapping or translation between the physical address space of the bus and the physical address space of the parent of the bus. For details, see "2.3.9 dma-ranges" in Devicetree Specification v0.4.
`io-channels`	`phandle-array`	IO channel specifiers relevant to the device.
`io-channel-names`	`string-array`	Optional names given to the IO channel specifiers in the "io-channels" property.
`mboxes`	`phandle-array`	Mailbox / IPM channel specifiers relevant to the device.
`mbox-names`	`string-array`	Optional names given to the mbox specifiers in the "mboxes" property.
`power-domains`	`phandle-array`	Power domain specifiers relevant to the device.
`power-domain-names`	`string-array`	Optional names given to the power domain specifiers in the "power-domains" property.
`#power-domain-cells`	`int`	Number of cells in power-domains property
`hwlocks`	`phandle-array`	HW spinlock id relevant to the device.
`hwlock-names`	`string-array`	Optional names given to the hwlock specifiers in the "hwlocks" property.
`zephyr,deferred-init`	`boolean`	Do not initialize device automatically on boot. Device should be manually initialized using device_init().
`wakeup-source`	`boolean`	Property to identify that a device can be used as wake up source. When this property is provided a specific flag is set into the device that tells the system that the device is capable of wake up the system. Wake up capable devices are disabled (interruptions will not wake up the system) by default but they can be enabled at runtime if necessary.
`zephyr,pm-device-runtime-auto`	`boolean`	Automatically configure the device for runtime power management after the init function runs.
`zephyr,disabling-power-states`	`phandles`	List of power states that will disable this device power.