infineon,airoc-wifi (on spi bus)

Vendor: Infineon Technologies

Note

An implementation of a driver matching this compatible is available in drivers/wifi/infineon.

Description

AIROC Wi-Fi Connectivity over SPI.

Properties

Node specific propertiesDeprecated node specific propertiesBase properties

Properties not inherited from the base binding file.

Name	Type	Details
wifi-host-wake-gpios	phandle-array	Host wake-up gpio. Signal from the AIROC Wi-Fi device to the host indicating that the device requires attention. This property is required.
bus-select-gpios	phandle-array	Select bus mode. This gpio must be held low before wifi-reg-on-gpios goes high to select SPI bus mode. This property is required.
spi-half-duplex	boolean	Use half-duplex communication; if not present, full- duplex operation is assumed.
spi-word-size	int	SPI word size in bits. Since 8-bit word size is the most common, that is selected as the default. Default value: 8 Legal values: 8, 16, 32
spi-data-irq-shared	boolean	SPI data and IRQ share the same GPIO.
spi-max-frequency	int	Maximum clock frequency of device's SPI interface in Hz This property is required.
duplex	int	Duplex mode, full or half. By default it's always full duplex thus 0 as this is, by far, the most common mode. Use the macros not the actual enum value, here is the concordance list (see dt-bindings/spi/spi.h) 0 SPI_FULL_DUPLEX 2048 SPI_HALF_DUPLEX Legal values: 0, 2048
frame-format	int	Motorola or TI frame format. By default it's always Motorola's, thus 0 as this is, by far, the most common format. Use the macros not the actual enum value, here is the concordance list (see dt-bindings/spi/spi.h) 0 SPI_FRAME_FORMAT_MOTOROLA 32768 SPI_FRAME_FORMAT_TI Legal values: 0, 32768
spi-cpol	boolean	SPI clock polarity which indicates the clock idle state. If it is used, the clock idle state is logic high; otherwise, low.
spi-cpha	boolean	SPI clock phase that indicates on which edge data is sampled. If it is used, data is sampled on the second edge; otherwise, on the first edge.
spi-hold-cs	boolean	In some cases, it is necessary for the master to manage SPI chip select under software control, so that multiple spi transactions can be performed without releasing it. A typical use case is variable length SPI packets where the first spi transaction reads the length and the second spi transaction reads length bytes.
supply-gpios	phandle-array	GPIO specifier that controls power to the device. This property should be provided when the device has a dedicated switch that controls power to the device. The supply state is entirely the responsibility of the device driver. Contrast with vin-supply.
vin-supply	phandle	Reference to the regulator that controls power to the device. The referenced devicetree node must have a regulator compatible. This property should be provided when device power is supplied by a shared regulator. The supply state is dependent on the request status of all devices fed by the regulator. Contrast with supply-gpios. If both properties are provided then the regulator must be requested before the supply GPIOS is set to an active state, and the supply GPIOS must be set to an inactive state before releasing the regulator.
wifi-reg-on-gpios	phandle-array	Power-up/down gpio to control the internal regulators used by the WiFi section of AIROC Wi-Fi device.
wifi-dev-wake-gpios	phandle-array	WiFi device wake-up gpio. Signal from the host to the AIROC Wi-Fi device indicating that the host requires attention.
pinctrl-0	phandles	Pin configuration/s for the first state. Content is specific to the selected pin controller driver implementation.
pinctrl-1	phandles	Pin configuration/s for the second state. See pinctrl-0.
pinctrl-2	phandles	Pin configuration/s for the third state. See pinctrl-0.
pinctrl-3	phandles	Pin configuration/s for the fourth state. See pinctrl-0.
pinctrl-4	phandles	Pin configuration/s for the fifth state. See pinctrl-0.
pinctrl-names	string-array	Names for the provided states. The number of names needs to match the number of states.