NXP LS1046A RDB
Overview
The LS1046A reference design board (RDB) is a high-performance computing, evaluation, and development platform that supports the Layerscape LS1046A architecture processor. The LS1046ARDB board supports the Layerscape LS1046A processor and is optimized to support the DDR4 memory and a full complement of high-speed SerDes ports.
The Layerscape LS1046A processor integrates four 64-bit Arm(R) Cortex(R) A72 cores with packet processing acceleration and high-speed peripherals. The impressive performance of more than 32,000 CoreMarks, paired with 10 Gb Ethernet, PCIe Gen. 3, SATA 3.0, USB 3.0 and QSPI interfaces provides an excellent combination for a range of enterprise and service provider networking, storage, security and industrial applications.
Hardware
LS1046A RDB boards supports the following features:
Four 32/64-bit Arm(R) Cortex(R)V8 A72 CPUs, up to 1.6 GHz core speed
Supports 8 GB DDR4 SDRAM memory
SDHC port connects directly to an adapter card slot, featuring 4 GB eMMCi memory device
One 512 MB SLC NAND flash with ECC support (1.8 V)
CPLD connection: 8-bit registers in CPLD to configure mux/demux selections
Support two 64 MB onboard QSPI NOR flash memories
USB: - Two USB 3.0 controllers with integrated PHYs. - One USB1 3.0 port is connected to a Type A host connector. - One USB1 3.0 port is configured as On-The-Go (OTG) with a Micro-AB connector. - One USB2.0 is connected to miniPCIe connector .
Ethernet: - Supports SGMII 1G PHYs at Lane 2 and Lane 3 - Supports SFP+module with XFI retimers - Supports AQR106/107 10G PHY with XFI/2.5G SGMII
PCIe and SATA: - Mini PCIe express x1 (Gen1/2/3)card - Standard PCIe x1 (Gen1/2/3) card - Standard PCIe x1 (Gen1/2/3) card - One SATA 3.0 connector
Supported Features
NXP LS1046A RDB board default configuration supports the following hardware features:
Interface |
Controller |
Driver/Component |
|---|---|---|
GIC-400 |
on-chip |
GICv2 interrupt controller |
ARM TIMER |
on-chip |
System Clock |
UART |
on-chip |
NS16550 compatible serial port |
Other hardware features have not been enabled yet for this board.
The default configuration can be found in the defconfig file for NON-SMP:
Or for SMP running on all four CPU Cores:
Or for SMP running on 2 CPU Cores (Core2 and Core3):
There are two serial port on the board: uart1 and uart2, Zephyr is using uart2 as serial console.
Programming and Debugging
Use the following configuration to run basic Zephyr applications and kernel tests on LS1046A RDB board. For example, with the Basic Synchronization sample:
Non-SMP mode
# From the root of the zephyr repository
west build -b ls1046ardb samples/synchronization
This will build an image with the synchronization sample app.
Use u-boot to load and kick Zephyr.bin to CPU Core0:
tftp c0000000 zephyr.bin; dcache off; dcache flush; icache flush; icache off; go 0xc0000000;
Or kick Zephyr.bin to any other CPU Cores, for example run Zephyr on Core3:
tftp c0000000 zephyr.bin; dcache off; dcache flush; icache flush; icache off; cpu 3 release 0xc0000000;
It will display the following console output:
*** Booting Zephyr OS build zephyr-v2.5.0-1922-g3265b69d47e7 ***
thread_a: Hello World from cpu 0 on nxp_ls1046ardb!
thread_b: Hello World from cpu 0 on nxp_ls1046ardb!
thread_a: Hello World from cpu 0 on nxp_ls1046ardb!
SMP mode running on 4 CPU Cores
# From the root of the zephyr repository
west build -b ls1046ardb/ls1046a/smp/4cores samples/synchronization
This will build an image with the synchronization sample app.
Use u-boot to load and kick Zephyr.bin to CPU Core0:
tftp c0000000 zephyr.bin; dcache off; dcache flush; icache flush; icache off; go 0xc0000000;
It will display the following console output:
*** Booting Zephyr OS build zephyr-v2.5.0-1922-g3265b69d47e7 ***
Secondary CPU core 1 (MPID:0x1) is up
Secondary CPU core 2 (MPID:0x2) is up
Secondary CPU core 3 (MPID:0x3) is up
thread_a: Hello World from cpu 0 on nxp_ls1046ardb!
thread_b: Hello World from cpu 1 on nxp_ls1046ardb!
thread_a: Hello World from cpu 0 on nxp_ls1046ardb!
SMP mode running on 2 CPU Cores: Core2 and Core3
# From the root of the zephyr repository
west build -b ls1046ardb/ls1046a/smp samples/synchronization
This will build an image with the synchronization sample app.
Use u-boot to load and kick Zephyr.bin to CPU Core2:
tftp c0000000 zephyr.bin; dcache off; dcache flush; icache flush; icache off; cpu 2 release 0xc0000000;
It will display the following console output:
*** Booting Zephyr OS build zephyr-v2.5.0-1922-g3265b69d47e7 ***
Secondary CPU core 1 (MPID:0x3) is up
thread_a: Hello World from cpu 0 on nxp_ls1046ardb!
thread_b: Hello World from cpu 1 on nxp_ls1046ardb!
thread_a: Hello World from cpu 0 on nxp_ls1046ardb!
Running Zephyr on Jailhouse inmate Cell
Use the following to run Zephyr in Jailhouse inmate, need to configure Jailhouse inmate Cell to use a single Core for Zephyr non-SMP mode, or use Core2 and Core3 for Zephyr SMP 2cores image.
Use root Cell dts to boot root Cell Linux.
Install Jailhouse module:
modprobe jailhouse
Run Zephyr demo in inmate Cell:
jailhouse enable ls1046a-rdb.cell
jailhouse cell create ls1046a-rdb-inmate-demo.cell
jailhouse cell load 1 zephyr.bin --address 0xc0000000
jailhouse cell start 1
Flashing
Zephyr image can be loaded in DDR memory at address 0xc0000000 from SD Card, EMMC, QSPI Flash or downloaded from network in uboot.
Debugging
LS1046A RDB board includes one JTAG connector on board, connect it to CodeWarrior TAP for debugging.