ST Nucleo F303K8
Overview
The Nucleo F303K8 board features an ARM Cortex-M4 based STM32F303K8 mixed-signal MCU with FPU and DSP instructions capable of running at 72 MHz. Here are some highlights of the Nucleo F303K8 board:
STM32 microcontroller in LQFP32 package
one type of extension resources:
Arduino™ Nano V3 connectivity support
On-board ST-LINK/V2-1 debugger/programmer with SWD connector
Flexible board power supply:
5 V from ST-LINK/V2-1 USB VBUS
External power sources: 3.3 V, 5V and 7 - 12 V
One user LED
One push-buttons: RESET
More information about the board can be found at the Nucleo F303K8 website, and in the STM32 Nucleo-32 board User Manual.
Hardware
The Nucleo F303K8 provides the following hardware components:
STM32F303K8T6 in LQFP32 package
ARM® 32-bit Cortex® -M4 CPU with FPU
72 MHz max CPU frequency
VDD from 2.0 V to 3.6 V
64 KB Flash
12 KB SRAM
RTC
Advanced-control Timer
General Purpose Timers (5)
Basic Timer (2)
Watchdog Timers (2)
PWM channels (12)
SPI/I2S (1)
I2C (1)
USART/UART (2)
CAN (1)
GPIO with external interrupt capability
DMA channels (7)
Capacitive sensing channels (18)
12-bit ADC with 21 channels
12-bit D/A converter
Analog comparator (3)
Op amp
More information about the STM32F303K8 can be found here:
Supported Features
The Zephyr nucleo_f303k8 board configuration supports the following hardware features:
Interface |
Controller |
Driver/Component |
|---|---|---|
NVIC |
on-chip |
nested vector interrupt controller |
UART |
on-chip |
serial port-polling; serial port-interrupt |
PINMUX |
on-chip |
pinmux |
GPIO |
on-chip |
gpio |
PWM |
on-chip |
pwm |
I2C |
on-chip |
i2c |
SPI |
on-chip |
spi |
ADC |
on-chip |
ADC Controller |
Other hardware features are not yet supported on this Zephyr port.
The default configuration can be found in boards/st/nucleo_f303k8/nucleo_f303k8_defconfig
Connections and IOs
The Nucleo F303K8 Board has 1 GPIO controller. This controllers is responsible for input/output, pull-up, etc.
Board connectors:
Default Zephyr Peripheral Mapping:
The Nucleo F303K8 board features an Arduino Zero V3 connector. Board is configured as follows:
UART_2 TX/RX : PA2/PA15 (ST-Link Virtual Port Com)
I2C1 SCL/SDA : PB7/PB6
SPI1 CS/SCK/MISO/MOSI : PA_4/PA_5/PA_6/PA_7
LD2 : PB3
System Clock
The Nucleo F303K8 System Clock can be driven by an internal or external oscillator, as well as by the main PLL clock. By default the System Clock is driven by the PLL clock at 72 MHz. The input to the PLL is an 8 MHz internal clock supply.
Serial Port
The Nucleo F303K8 board has 2 UARTs. The Zephyr console output is assigned to UART2. Default settings are 115200 8N1.
Programming and Debugging
The Nucleo F303K8 board includes an ST-LINK/V2-1 embedded debug tool interface. This interface is supported by the openocd version included in Zephyr SDK.