The latest development version of this page may be more current than this released 3.7.0 version.

ST STM32F4 Discovery

Overview

The STM32F4DISCOVERY Discovery kit features an ARM Cortex-M4 based STM32F407VG MCU with a wide range of connectivity support and configurations Here are some highlights of the STM32F4DISCOVERY board:

  • STM32 microcontroller in LQFP100 package

  • Extension header for all LQFP100 I/Os for quick connection to prototyping board and easy probing

  • On-board ST-LINK/V2 debugger/programmer with SWD connector

  • Flexible board power supply:

    • USB VBUS or external source(3.3V, 5V, 7 - 12V)

    • Power management access point

  • Eight LEDs:

    • USB communication (LD1)

    • 3.3 V power on (LD2)

    • Four user LEDs: orange (LD3), green (LD4), red (LD5), and blue (LD6)

    • 2 USB OTG LEDs for VBUS (LD7) and over-current (LD8)

  • Two push-buttons: USER and RESET

  • USB OTG FS with micro-AB connector

  • LIS302DL or LIS3DSH ST MEMS 3-axis accelerometer

  • MP45DT02 ST-MEMS audio sensor omni-directional digital microphone

  • CS43L22 audio DAC with integrated class D speaker driver

STM32F4DISCOVERY

More information about the board can be found at the STM32F4DISCOVERY website.

Hardware

STM32F4DISCOVERY Discovery kit provides the following hardware components:

  • STM32F407VGT6 in LQFP100 package

  • ARM® 32-bit Cortex® -M4 CPU with FPU

  • 168 MHz max CPU frequency

  • VDD from 1.8 V to 3.6 V

  • 1 MB Flash

  • 192+4 KB SRAM including 64-Kbyte of core coupled memory

  • GPIO with external interrupt capability

  • 3x12-bit ADC with 24 channels

  • 2x12-bit D/A converters

  • RTC

  • Advanced-control Timer

  • General Purpose Timers (17)

  • Watchdog Timers (2)

  • USART/UART (6)

  • I2C (3)

  • SPI (3)

  • SDIO

  • 2xCAN

  • USB 2.0 OTG FS with on-chip PHY

  • USB 2.0 OTG HS/FS with dedicated DMA, on-chip full-speed PHY and ULPI

  • 10/100 Ethernet MAC with dedicated DMA

  • 8- to 14-bit parallel camera

  • CRC calculation unit

  • True random number generator

  • DMA Controller

More information about STM32F407VG can be found here:

Supported Features

The Zephyr stm32f4_disco board configuration supports the following hardware features:

Interface

Controller

Driver/Component

NVIC

on-chip

nested vector interrupt controller

UART

on-chip

serial port-polling; serial port-interrupt

PINMUX

on-chip

pinmux

GPIO

on-chip

gpio

PWM

on-chip

pwm

USB

on-chip

usb

CAN

on-chip

CAN controller

Note

CAN feature requires CAN transceiver, such as SK Pang CAN breakout board. Zephyr default configuration uses CAN_2 exclusively, as simultaneous use of CAN_1 and CAN_2 is not yet supported.

Other hardware features are not yet supported on Zephyr porting.

The default configuration can be found in boards/st/stm32f4_disco/stm32f4_disco_defconfig

Pin Mapping

STM32F4DISCOVERY Discovery kit has 8 GPIO controllers. These controllers are responsible for pin muxing, input/output, pull-up, etc.

For more details please refer to STM32F4DISCOVERY board User Manual.

Default Zephyr Peripheral Mapping:

  • UART_1_TX : PB6

  • UART_1_RX : PB7

  • UART_2_TX : PA2

  • UART_2_RX : PA3

  • USER_PB : PA0

  • LD3 : PD13

  • LD4 : PD12

  • LD5 : PD14

  • LD6 : PD15

  • USB DM : PA11

  • USB DP : PA12

  • CAN1_RX : PB8

  • CAN1_TX : PB9

  • CAN2_RX : PB5

  • CAN2_TX : PB13

System Clock

STM32F4DISCOVERY System Clock could be driven by internal or external oscillator, as well as main PLL clock. By default System clock is driven by PLL clock at 168MHz, driven by 8MHz high speed external clock.

Serial Port

STM32F4DISCOVERY Discovery kit has up to 6 UARTs. The Zephyr console output is assigned to UART2. Default settings are 115200 8N1. Please note that ST-Link Virtual Com Port is not wired to chip serial port. In order to enable console output you should use a serial cable and connect it to UART2 pins (PA2/PA3).

Programming and Debugging

Applications for the stm32f4_disco board configuration can be built and flashed in the usual way (see Building an Application and Run an Application for more details).

Flashing

STM32F4DISCOVERY Discovery kit includes an ST-LINK/V2 embedded debug tool interface. This interface is supported by the openocd version included in Zephyr SDK.

Flashing an application to STM32F4DISCOVERY

Here is an example for the Blinky application.

Run a serial host program to connect with your board:

$ minicom -D /dev/ttyACM0

Build and flash the application:

# From the root of the zephyr repository
west build -b stm32f4_disco samples/basic/blinky
west flash

You should see user led “LD4” blinking.

Debugging

You can debug an application in the usual way. Here is an example for the Hello World application.

# From the root of the zephyr repository
west build -b stm32f4_disco samples/hello_world
west debug