The latest development version of this page may be more current than this released 4.0.0 version.

RA6M5 Evaluation Kit

Overview

The Renesas RA6M5 group uses the high-performance Arm® Cortex®-M33 core with TrustZone®. The RA6M5 is suitable for IoT applications requiring Ethernet, future proof security, large embedded RAM, and low active power consumption down to 107uA/MHz running the CoreMark® algorithm from Flash.

The key features of the EK-RA6M5 board are categorized in three groups as follow:

MCU Native Pin Access

  • 200MHz Arm Cortex-M33 based RA6M5 MCU in 176 pins, LQFP package

  • Native pin access through 4 x 40-pin male headers

  • MCU current measurement points for precision current consumption measurement

  • Multiple clock sources - RA6M5 MCU oscillator and sub-clock oscillator crystals, providing precision 24.000 MHz and 32,768 Hz reference clock. Additional low precision clocks are avaialbe internal to the RA6M5 MCU

System Control and Ecosystem Access

  • USB Full Speed Host and Device (micro-AB connector)

  • Four 5V input sources

    • USB (Debug, Full Speed, High Speed)

    • External power supply (using surface mount clamp test points and power input vias)

  • Three Debug modes

    • Debug on-board (SWD)

    • Debug in (ETM, SWD and JTAG)

    • Debug out (SWD)

  • User LEDs and buttons

    • Three User LEDs (red, blue, green)

    • Power LED (white) indicating availability of regulated power

    • Debug LED (yellow) indicating the debug connection

    • Two User buttons

    • One Reset button

  • Five most popular ecosystems expansions

    • Two Seeed Grove system (I2C/Analog) connectors

    • One SparkFun Qwiic connector

    • Two Digilent Pmod (SPI and UART) connectors

    • Arduino (Uno R3) connector

    • MikroElektronika mikroBUS connector

  • MCU boot configuration jumper

Special Feature Access

  • Ethernet (RJ45 RMII interface)

  • USB High Speed Host and Device (micro-AB connector)

  • 32 Mb (256 Mb) External Quad-SPI Flash

  • 64 Mb (512 Mb) External Octo-SPI Flash

  • CAN (3-pin header)

RA6M5 Evaluation Kit

EK-RA6M5 Board Functional Area Definitions (Credit: Renesas Electronics Corporation)

Hardware

Detailed hardware feature for the RA6M5 MCU group can be found at RA6M5 Group User’s Manual Hardware

RA6M5 MCU group feature

RA6M5 Block diagram (Credit: Renesas Electronics Corporation)

Detailed hardware feature for the EK-RA6M5 MCU can be found at EK-RA6M5 - User’s Manual

Supported Features

The below features are currently supported on Zephyr OS for EK-RA6M5 board:

Interface

Controller

Driver/Component

GPIO

on-chip

gpio

MPU

on-chip

arch/arm

NVIC

on-chip

arch/arm

UART

on-chip

serial

CLOCK

on-chip

clock control

Other hardware features are currently not supported by the port.

Programming and Debugging

Applications for the ek_ra6m5 board target configuration can be built, flashed, and debugged in the usual way. See Building an Application and Run an Application for more details on building and running.

Flashing

Program can be flashed to EK-RA6M5 via the on-board SEGGER J-Link debugger. SEGGER J-link’s drivers are avaialbe at https://www.segger.com/downloads/jlink/

To flash the program to board

  1. Connect to J-Link OB via USB port to host PC

  2. Make sure J-Link OB jumper is in default configuration as describe in EK-RA6M5 - User’s Manual

  3. Execute west command

    west flash -r jlink

Debugging

You can use Segger Ozone (Segger Ozone Download) for a visual debug interface

Once downloaded and installed, open Segger Ozone and configure the debug project like so:

  • Target Device: R7FA6M5BH

  • Target Interface: SWD

  • Target Interface Speed: 4 MHz

  • Host Interface: USB

  • Program File: <path/to/your/build/zephyr.elf>

Note: It’s verified that we can debug OK on Segger Ozone v3.30d so please use this or later version of Segger Ozone

References