RA6M4 Evaluation Kit
Overview
The Renesas RA6M4 group uses the high-performance Arm® Cortex®-M33 core with TrustZone®. Secure element functionality providing better performance, unlimited secure key storage, key management, and lower BOM cost, as well as the integrated Ethernet MAC with individual DMA ensures high data throughput. The RA6M4 is suitable for IoT applications requiring Ethernet, future proof security, large embedded RAM, and low active power consumption down to 99uA/MHz running the CoreMark® algorithm from Flash.
The key features of the EK-RA6M4 board are categorized in three groups as follow:
MCU Native Pin Access
200MHz Arm Cortex-M33 based RA6M4 MCU in 144 pins, LQFP package
Native pin access through 4 x 40-pin male headers
MCU current measurement points for precision current consumption measurement
Multiple clock sources - RA6M4 MCU oscillator and sub-clock oscillator crystals, providing precision 24.000 MHz and 32,768 Hz reference clock. Additional low precision clocks are avaialbe internal to the RA6M4 MCU
System Control and Ecosystem Access
USB Full Speed Host and Device (micro-AB connector)
Three 5 V input sources
USB (Debug, Full Speed)
External power supply (using surface mount clamp test points and power input vias)
Three Debug modes
Debug on-board (SWD)
Debug in (ETM, SWD and JTAG)
Debug out (SWD)
User LEDs and buttons
Three User LEDs (red, blue, green)
Power LED (white) indicating availability of regulated power
Debug LED (yellow) indicating the debug connection
Two User buttons
One Reset button
Five most popular ecosystems expansions
Two Seeed Grove system (I2C/Analog) connectors
One SparkFun Qwiic connector
Two Digilent Pmod (SPI and UART) connectors
Arduino (Uno R3) connector
MikroElektronika mikroBUS connector
MCU boot configuration jumper
Special Feature Access
Ethernet (RJ45 RMII interface)
32 Mb (256 Mb) External Quad-SPI Flash
64 Mb (512 Mb) External Octo-SPI Flash
EK-RA6M4 Board Functional Area Definitions (Credit: Renesas Electronics Corporation)
Hardware
Detailed hardware feature for the RA6M4 MCU group can be found at RA6M4 Group User’s Manual Hardware
RA6M4 Block diagram (Credit: Renesas Electronics Corporation)
Detailed hardware feature for the EK-RA6M4 MCU can be found at EK-RA6M4 - User’s Manual
Supported Features
The below features are currently supported on Zephyr OS for EK-RA6M4 board:
Interface |
Controller |
Driver/Component |
|---|---|---|
GPIO |
on-chip |
gpio |
MPU |
on-chip |
arch/arm |
NVIC |
on-chip |
arch/arm |
UART |
on-chip |
serial |
CLOCK |
on-chip |
clock control |
Other hardware features are currently not supported by the port.
Programming and Debugging
Applications for the ek_ra6m4 board target configuration can be
built, flashed, and debugged in the usual way. See
Building an Application and Run an Application for more details on
building and running.
Flashing
Program can be flashed to EK-RA6M4 via the on-board SEGGER J-Link debugger. SEGGER J-link’s drivers are avaialbe at https://www.segger.com/downloads/jlink/
To flash the program to board
Connect to J-Link OB via USB port to host PC
Make sure J-Link OB jumper is in default configuration as describe in EK-RA6M4 - User’s Manual
Execute west command
west flash -r jlink
Debugging
You can use Segger Ozone (Segger Ozone Download) for a visual debug interface
Once downloaded and installed, open Segger Ozone and configure the debug project like so:
Target Device: R7FA6M4AF
Target Interface: SWD
Target Interface Speed: 4 MHz
Host Interface: USB
Program File: <path/to/your/build/zephyr.elf>
Note: It’s verified that we can debug OK on Segger Ozone v3.30d so please use this or later version of Segger Ozone