ROCK 5B
Overview
The Radxa ROCK 5B is a single-board computer based on the Rockchip RK3588 SoC. The SoC combines four Arm Cortex-A76 and four Arm Cortex-A55 CPU cores. The board is available with up to 16 GB of LPDDR4X memory and provides eMMC, microSD, PCIe, USB, Ethernet, and a 40-pin expansion header.
The SMP variant supports all four Cortex-A55 and four Cortex-A76 cores.
Hardware
The ROCK 5B includes the following hardware features:
Rockchip RK3588 SoC
Four Arm Cortex-A76 cores up to 2.4 GHz and four Arm Cortex-A55 cores up to 1.8 GHz
Arm Mali-G610 MP4 GPU and neural processing unit (NPU) with up to 6 TOPS
64-bit LPDDR4X memory, available in 4 GB, 8 GB, and 16 GB variants
eMMC connector and microSD card slot
M.2 E Key connector with PCIe 2.1 x1, USB, SATA, SDIO, PCM, and UART signals for Wi-Fi 6 modules
M.2 M Key connector with a PCIe 3.0 x4 interface for 2280 NVMe SSDs
2.5 Gigabit Ethernet with Power over Ethernet (PoE) support (requires an optional PoE HAT)
Two USB 2.0 host ports and two USB 3.0 host/OTG ports
Two HDMI outputs, one DisplayPort output over USB Type-C, and one MIPI DSI output
One Micro HDMI input port
One MIPI CSI camera interface
40-pin expansion header
USB Type-C power delivery (PD 2.0)
100 mm x 75 mm board size
Supported Features
The rock_5b board supports the hardware features listed below.
- on-chip / on-board
- Feature integrated in the SoC / present on the board.
- 2 / 2
-
Number of instances that are enabled / disabled.
Click on the label to see the first instance of this feature in the board/SoC DTS files. -
vnd,foo -
Compatible string for the Devicetree binding matching the feature.
Click on the link to view the binding documentation.
rock_5b/rk3588 target
On-target memory for this board target: 128 MiB of RAM, N/A of Flash.
Type |
Location |
Description |
Compatible |
|---|---|---|---|
CPU |
on-chip |
ARM Cortex-A55 CPU4 |
|
on-chip |
ARM Cortex-A76 CPU4 |
||
Clock control |
on-chip |
Rockchip RK3588 CRU1 |
|
on-chip |
Rockchip RK3588 CRU Clock Controller1 |
||
Ethernet |
on-chip |
Rockchip RK3588 GMAC2 |
|
on-chip |
Synopsys DesignWare MAC MDIO controller2 |
||
on-chip |
Synopsys DesignWare MAC PTP (Precision Time Protocol) Clock2 |
||
Interrupt controller |
on-chip |
ARM Generic Interrupt Controller v31 |
|
Power management CPU operations |
on-chip |
Power State Coordination Interface (PSCI) version 0.21 |
|
Reset controller |
on-chip |
Rockchip RK3588 CRU Reset Controller1 |
|
Serial controller |
on-chip |
||
SRAM |
on-board |
Generic on-chip SRAM1 |
|
System controller |
on-chip |
System Controller Registers R/W2 |
|
Timer |
on-chip |
per-core ARM architected timer1 |
rock_5b/rk3588/smp target
On-target memory for this board target: 128 MiB of RAM, N/A of Flash.
Type |
Location |
Description |
Compatible |
|---|---|---|---|
CPU |
on-chip |
ARM Cortex-A55 CPU4 |
|
on-chip |
ARM Cortex-A76 CPU4 |
||
Clock control |
on-chip |
Rockchip RK3588 CRU1 |
|
on-chip |
Rockchip RK3588 CRU Clock Controller1 |
||
Ethernet |
on-chip |
Rockchip RK3588 GMAC2 |
|
on-chip |
Synopsys DesignWare MAC MDIO controller2 |
||
on-chip |
Synopsys DesignWare MAC PTP (Precision Time Protocol) Clock2 |
||
Interrupt controller |
on-chip |
ARM Generic Interrupt Controller v31 |
|
Power management CPU operations |
on-chip |
Power State Coordination Interface (PSCI) version 0.21 |
|
Reset controller |
on-chip |
Rockchip RK3588 CRU Reset Controller1 |
|
Serial controller |
on-chip |
||
SRAM |
on-board |
Generic on-chip SRAM1 |
|
System controller |
on-chip |
System Controller Registers R/W2 |
|
Timer |
on-chip |
per-core ARM architected timer1 |
The onboard Ethernet interface is not currently supported by Zephyr.
Serial Port
Zephyr uses UART2 as the serial console at 1.5 Mbit/s. On the 40-pin expansion header, connect GND to pin 6, the adapter RX input to the board TX output on pin 8, and the adapter TX output to the board RX input on pin 10. The adapter must support 1.5 Mbaud; use 1500000 baud, 8 data bits, no parity, one stop bit, and no flow control. The Radxa serial console documentation describes the same connection in more detail.
Programming and Debugging
The rock_5b board supports the runners and associated west commands listed below.
| flash | debug |
|---|
Applications are built with the standard configuration, for example:
# From the root of the zephyr repository
west build -b rock_5b samples/hello_world
To run Zephyr on all eight CPU cores, build the SMP variant:
# From the root of the zephyr repository
west build -b rock_5b//smp samples/synchronization
Create a legacy U-Boot image whose payload loads and runs at 0x10000000:
mkimage -C none -A arm64 -O linux -a 0x10000000 -e 0x10000000 \
-d build/zephyr/zephyr.bin build/zephyr/zephyr.img
The Radxa U-Boot AArch64 Linux boot path requires a devicetree. Obtain
rk3588-rock-5b.dtb from the Radxa Linux distribution and copy it and
zephyr.img to a FAT partition accessible from U-Boot.
Check the temporary kernel and devicetree load addresses provided by U-Boot:
printenv kernel_addr_r fdt_addr_r
Load each file at its corresponding address, then pass the devicetree address
to bootm. Adjust the MMC device and partition numbers for the selected boot
media:
fatload mmc 1:1 ${kernel_addr_r} zephyr.img
fatload mmc 1:1 ${fdt_addr_r} rk3588-rock-5b.dtb
bootm ${kernel_addr_r} - ${fdt_addr_r}
The legacy image header instructs U-Boot to move the Zephyr payload from
kernel_addr_r to 0x10000000 before jumping to the entry point. Keeping
the temporary image, devicetree, and Zephyr runtime regions separate avoids
overwriting any of them during the handoff.
References
More information is available from the Radxa ROCK 5B documentation.