Pico2-SPE
Overview
The Pico2-SPE is a small, low-cost, versatile boards from KWS Computersysteme Gmbh. They are equipped with an RP2350a SoC, an on-board LED, a USB connector, an SWD interface. The Pico2-SPE additionally contains an Microchip LAN8651 10Base-T1S module. The USB bootloader allows the ability to flash without any adapter, in a drag-and-drop manner. It is also possible to flash and debug the boards with their SWD interface, using an external adapter.
Hardware
Dual Cortex-M33 or Hazard3 processors at up to 150MHz
520KB of SRAM, and 4MB of on-board flash memory
USB 1.1 with device and host support
Low-power sleep and dormant modes
Drag-and-drop programming using mass storage over USB
26 multi-function GPIO pins including 3 that can be used for ADC
1 SPI, 2 I2C, 2 UART, 3 12-bit 500ksps Analogue to Digital - Converter (ADC), 24 controllable PWM channels
2 Timer with 4 alarms, 1 AON Timer
Temperature sensor
Microchip LAN8651 10Base-T1S
3 Programmable IO (PIO) blocks, 12 state machines total for custom peripheral support
Flexible, user-programmable high-speed IO
Can emulate interfaces such as SD Card and VGA
Supported Features
The pico2_spe board supports the hardware features listed below.
- on-chip / on-board
- Feature integrated in the SoC / present on the board.
- 2 / 2
-
Number of instances that are enabled / disabled.
Click on the label to see the first instance of this feature in the board/SoC DTS files. -
vnd,foo -
Compatible string for the Devicetree binding matching the feature.
Click on the link to view the binding documentation.
Type |
Location |
Description |
Compatible |
|---|---|---|---|
CPU |
on-chip |
ARM Cortex-M33 CPU2 |
|
ADC |
on-chip |
Raspberry Pi Pico ADC1 |
|
Clock control |
on-chip |
||
on-chip |
The representation of Raspberry Pi Pico’s PLL2 |
||
on-chip |
The representation of Raspberry Pi Pico ring oscillator1 |
||
on-chip |
The representation of Raspberry Pi Pico external oscillator1 |
||
on-chip |
Raspberry Pi Pico clock controller node1 |
||
Counter |
on-chip |
||
DMA |
on-chip |
Raspberry Pi Pico DMA1 |
|
Ethernet |
on-board |
LAN865x standalone 10BASE-T1L Ethernet controller with SPI interface1 |
|
on-board |
Microchip’s 10BASE-T1S PHYs support1 |
||
Flash controller |
on-chip |
Raspberry Pi Pico flash controller1 |
|
GPIO & Headers |
on-chip |
Raspberry Pi Pico GPIO1 |
|
on-chip |
|||
on-board |
GPIO pins exposed on Raspberry Pi Pico headers1 |
||
I2C |
on-chip |
Raspberry Pi Pico I2C2 |
|
Interrupt controller |
on-chip |
ARMv8-M NVIC (Nested Vectored Interrupt Controller)1 |
|
Miscellaneous |
on-chip |
Raspberry Pi Pico PIO3 |
|
MTD |
on-chip |
Flash node1 |
|
on-board |
Fixed partitions of a flash (or other non-volatile storage) memory1 |
||
Pin control |
on-chip |
The RPi Pico pin controller is a node responsible for controlling pin function selection and pin properties, such as routing a UART0 Rx to pin 1 and enabling the pullup resistor on that pin1 |
|
PWM |
on-chip |
Raspberry Pi Pico PWM1 |
|
Reset controller |
on-chip |
Raspberry Pi Pico Reset Controller1 |
|
Sensors |
on-chip |
Raspberry Pi Pico family temperature sensor node1 |
|
Serial controller |
on-chip |
||
SPI |
on-chip |
||
SRAM |
on-chip |
Generic on-chip SRAM1 |
|
Timer |
on-chip |
ARMv8-M System Tick1 |
|
USB |
on-chip |
Raspberry Pi Pico USB Device Controller1 |
|
Watchdog |
on-chip |
Raspberry Pi Pico Watchdog1 |
Connections and IOs
The default pin mapping is unchanged from the Pico-SPE.
Programming and Debugging
The pico2_spe board supports the runners and associated west commands listed below.
| flash | debug | attach | rtt | debugserver | |
|---|---|---|---|---|---|
| openocd | ✅ (default) | ✅ (default) | ✅ | ✅ | ✅ |
| uf2 | ✅ |
As with the Pico-SPE, the SWD interface can be used to program and debug the device, e.g. using OpenOCD with the Raspberry Pi Debug Probe .