This is the documentation for the latest (main) development branch of Zephyr. If you are looking for the documentation of previous releases, use the drop-down menu on the left and select the desired version.

NXP X-S32Z27X-DC (DC2)


The X-S32Z27X-DC (DC2) board is based on the NXP S32Z2 Real-Time Processor, which includes two Real-Time Units (RTU) composed of four ARM Cortex-R52 cores each, with flexible split/lock configurations.

There is one Zephyr board per SoC/RTU:

  • s32z2xxdc2/s32z270/rtu0, for S32Z270/RTU0

  • s32z2xxdc2/s32z270/rtu1, for S32Z270/RTU1.


Information about the hardware and design resources can be found at NXP S32Z2 Real-Time Processors website [1].

Supported Features

The boards support the following hardware features:







Arm Timer

















external interrupt controller










Other hardware features are not currently supported by the port.

Connections and IOs

The SoC’s pads are grouped into ports and pins for consistency with GPIO driver and the HAL drivers used by this Zephyr port. The following table summarizes the mapping between pads and ports/pins. This must be taken into account when using GPIO driver or configuring the pinmuxing for the device drivers.



PAD_000 - PAD_015

PA0 - PA15

PAD_016 - PAD_030

PB0 - PB14



PAD_032 - PAD_047

PD0 - PD15

PAD_048 - PAD_063

PE0 - PE15

PAD_064 - PAD_079

PF0 - PF15

PAD_080 - PAD_091

PG0 - PG11

PAD_092 - PAD_095

PH12 - PH15

PAD_096 - PAD_111

PI0 - PI15

PAD_112 - PAD_127

PJ0 - PJ15

PAD_128 - PAD_143

PK0 - PK15

PAD_144 - PAD_145

PL0 - PL1

PAD_146 - PAD_159

PM2 - PM15

PAD_160 - PAD_169

PN0 - PN9

PAD_170 - PAD_173

PO10 - PO13

This board does not include user LED’s or switches, which are needed for some of the samples such as Blinky or Button. Follow the steps described in the sample description to enable support for this board.

System Clock

The Cortex-R52 cores are configured to run at 800 MHz.

Serial Port

The SoC has 12 LINFlexD instances that can be used in UART mode. The console can be accessed by default on the USB micro-B connector J119.


The watchdog driver only supports triggering an interrupt upon timer expiration. Zephyr is currently running from SRAM on this board, thus system reset is not supported.


NETC driver supports to manage the Physical Station Interface (PSI0) and/or a single Virtual SI (VSI). The rest of the VSI’s shall be assigned to different cores of the system. Refer to NXP S32 NETC Sample Application to learn how to configure the Ethernet network controller.

Controller Area Network (CAN)

Currently, the CANXL transceiver is not populated in this board. So CAN transceiver connection is required for running external traffic. We can use any CAN transceiver, which supports CAN 2.0 and CAN FD protocol.

CAN driver supports classic (CAN 2.0) and CAN FD mode. Remote transmission request is not supported as this feature is not available on NXP S32 CANXL HAL.

Programming and Debugging

Applications for the s32z2xxdc2 boards can be built in the usual way as documented in Building an Application.

Currently is only possible to load and execute a Zephyr application binary on this board from the core internal SRAM.

This board supports West runners for the following debug tools:

Follow the installation steps of the debug tool you plan to use before loading your firmware.

Set-up the Board

Connect the external debugger probe to the board’s JTAG connector (J134) and to the host computer via USB or Ethernet, as supported by the probe.

For visualizing the serial output, connect the board’s USB/UART port (J119) to the host computer and run your favorite terminal program to listen for output. For example, using the cross-platform pySerial miniterm [2] terminal:

python -m <port> 115200

Replace <port> with the port where the board can be found. For example, under Linux, /dev/ttyUSB0.


You can build and debug the Hello World sample for the board s32z2xxdc2/s32z270/rtu0 with:

# From the root of the zephyr repository
west build -b s32z2xxdc2/s32z270/rtu0 samples/hello_world
west debug

In case you are using a newer PCB revision, you have to use an adapted board definition as the default PCB revision is B. For example, if using revision D:

west build -b s32z2xxdc2@D/s32z270/rtu0 samples/hello_world
west debug

At this point you can do your normal debug session. Set breakpoints and then c to continue into the program. You should see the following message in the terminal:

Hello World! s32z2xxdc2

To debug with Lauterbach TRACE32 softare run instead:

west build -b s32z2xxdc2/s32z270/rtu0 samples/hello_world
west debug
west build -t -r
west build -t trace32


Follow these steps if you just want to download the application to the board SRAM and run.

flash command is supported only by the Lauterbach TRACE32 runner:

west build -b s32z2xxdc2/s32z270/rtu0 samples/hello_world
west flash
west build -t -r
west build -t trace32


Currently, the Lauterbach start-up scripts executed with flash and debug commands perform the same steps to initialize the SoC and load the application to SRAM. The difference is that flash hides the Lauterbach TRACE32 interface, executes the application and exits.

To imitate a similar behavior using NXP S32 Debug Probe runner, you can run the debug command with GDB in batch mode:

west build -b s32z2xxdc2/s32z270/rtu0 samples/hello_world
west debug
west build -t --tool-opt='--batch'

RTU and Core Configuration

This Zephyr port can only run single core in any of the Cortex-R52 cores, either in lock-step or split-lock mode. By default, Zephyr runs on the first core of the RTU chosen and in lock-step mode (which is the reset configuration).

To build for split-lock mode, the CONFIG_DCLS must be disabled from your application Kconfig file.

By default the board configuration will set the runner arguments according to the build configuration. To debug for a core different than the default use:

west debug --core-name='R52_<rtu_id>_<core_id>_LS'


  • <rtu_id> is the zero-based RTU index

  • <core_id> is the zero-based core index relative to the RTU on which to run the Zephyr application (0, 1, 2 or 3)

For example, to build the Hello World sample for the board s32z2xxdc2/s32z270/rtu0 with split-lock core configuration:

west build -b s32z2xxdc2/s32z270/rtu0 samples/hello_world -- -DCONFIG_DCLS=n

To execute this sample in the second core of RTU0 in split-lock mode:

west debug --core-name='R52_0_1'

If using Lauterbach TRACE32, all runner parameters must be overridden from command line:

west debug --startup-args elfFile=<elf_path> rtu=<rtu_id> core=<core_id> lockstep=<yes/no>

Where <elf_path> is the path to the Zephyr application ELF in the output directory.