Wio-WM1110 Dev Kit
Overview
The Wio-WM1110 Dev Kit is based on the Wio-WM1110 Wireless Module. This module integrates a LoRa® transceiver and a multi-purpose radio front-end for geolocation. The LoRa® transceiver provides low-power network coverage, while GNSS (GPS/Beidou) and Wi-Fi scanning offer location coverage while also providing connectivity options for a variety of peripherals.
Hardware
Wio-WM1110 Dev Kit featuring:
Accelerometer, LIS3DHTR
Temperature and humidity sensor, SHT41
Two user LEDs (green and red)
Three buttons (two user and one reset)
Three Grove connectors
USB Type-C connector
GNSS antenna connector
LoRa antenna connector
NFC antenna IPEX connector
Support for solar and battery power
For more information about Wio-WM1110 Dev Kit: Wio-WM1110 Dev Kit Product Page.
The Wio-WM1110 Wireless Module is embedded with Nordic Semiconductor nRF52840 and Semtech LR1110. In this module the nRF52840 is intended to be used as an application processor and the LR1110 interfaces with it via SPI. Most of the interfaces and pins exposed in this board are on nRF52840.
For more information about Wio-WM1110 Wireless Module: Wio-WM1110 Wireless Module Product Page.
Nordic Semiconductor nRF52840 featuring:
ARM® Cortex®-M4 32-bit processor with FPU, 64 MHz
Bluetooth®5, IEEE 802.15.4-2006, 2.4 GHz transceiver
1 MB flash and 256 kB RAM
ARM® TrustZone® Cryptocell 310 security subsystem
Secure boot
For more information about Nordic Semiconductor nRF52840: Nordic Semiconductor nRF52840 Product Page.
Semtech LR1110 featuring:
Worldwide ISM frequency bands support in the range 150 - 960MHz
GNSS (GPS/ BeiDou) low-power scanning
802.11b/g/n Wi-Fi ultra-low-power passive scanning
150 - 2700MHz continuous frequency synthesizer range
Hardware support for AES-128 encryption/decryption based algorithms
For more information about Semtech LR1110: Semtech LR1110 Product Page.
Supported Features
The wio_wm1110_dev_kit
board supports the hardware features listed below.
- on-chip / on-board
- Feature integrated in the SoC / present on the board.
- 2 / 2
-
Number of instances that are enabled / disabled.
Click on the label to see the first instance of this feature in the board/SoC DTS files. -
vnd,foo
-
Compatible string for the Devicetree binding matching the feature.
Click on the link to view the binding documentation.
wio_wm1110_dev_kit/nrf52840
target
Type |
Location |
Description |
Compatible |
---|---|---|---|
CPU |
on-chip |
ARM Cortex-M4F CPU1 |
|
ADC |
on-chip |
Nordic Semiconductor nRF family SAADC node1 |
|
ARM architecture |
on-chip |
Nordic UICR (User Information Configuration Registers)1 |
|
on-chip |
Nordic EGU (Event Generator Unit)6 |
||
on-chip |
Nordic nRF family ACL (Access Control List)1 |
||
on-chip |
Nordic nRF family MWU (Memory Watch Unit)1 |
||
Audio |
on-chip |
Nordic PDM (Pulse Density Modulation interface)1 |
|
Clock control |
on-chip |
Nordic nRF clock control node1 |
|
on-chip |
Nordic nRF high-frequency crystal oscillator (nRF52 series)1 |
||
Comparator |
on-chip |
Nordic nRF COMP (analog COMParator)1 |
|
Counter |
on-chip |
Nordic nRF timer node5 |
|
Cryptographic accelerator |
on-chip |
Nordic ECB (AES electronic codebook mode encryption)1 |
|
on-chip |
Nordic nRF family CCM (AES CCM mode encryption)1 |
||
on-chip |
ARM TrustZone CryptoCell 3101 |
||
Debug |
on-chip |
ARMv7 instrumentation trace macrocell1 |
|
Flash controller |
on-chip |
Nordic NVMC (Non-Volatile Memory Controller)1 |
|
on-chip |
Properties defining the interface for the Nordic QSPI peripheral1 |
||
GPIO & Headers |
on-chip |
NRF5 GPIOTE1 |
|
on-chip |
NRF5 GPIO2 |
||
I2C |
on-chip |
||
I2S |
on-chip |
Nordic I2S (Inter-IC sound interface)1 |
|
IEEE 802.15.4 |
on-chip |
Nordic nRF IEEE 802.15.4 node1 |
|
Input |
on-board |
Group of GPIO-bound input keys1 |
|
Interrupt controller |
on-chip |
ARMv7-M NVIC (Nested Vectored Interrupt Controller)1 |
|
LED |
on-board |
Group of GPIO-controlled LEDs1 |
|
Miscellaneous |
on-chip |
Nordic FICR (Factory Information Configuration Registers)1 |
|
on-chip |
Nordic nRF family PPI (Programmable Peripheral Interconnect)1 |
||
MTD |
on-chip |
Flash node1 |
|
on-chip |
Fixed partitions of a flash (or other non-volatile storage) memory1 |
||
Networking |
on-chip |
Nordic nRF family RADIO peripheral1 |
|
on-chip |
Nordic nRF family NFCT (Near Field Communication Tag)1 |
||
Pin control |
on-chip |
Nordic nRF family Pin Controller1 |
|
Power management |
on-chip |
Nordic nRF power control node1 |
|
PWM |
on-chip |
nRF PWM4 |
|
on-chip |
nRFx S/W PWM1 |
||
Regulator |
on-chip |
Nordic nRF5X regulator (fixed stage of the core supply)1 |
|
on-chip |
Nordic nRF52X regulator (high voltage stage of the main supply)1 |
||
Retained memory |
on-chip |
Nordic GPREGRET (General Purpose Register Retention) device2 |
|
RNG |
on-chip |
Nordic nRF family RNG (Random Number Generator)1 |
|
RTC |
on-chip |
Nordic nRF RTC (Real-Time Counter)3 |
|
Sensors |
on-board |
STMicroelectronics LIS3DH 3-axis accelerometer1 |
|
on-board |
Sensirion SHT4x humidity and temperature sensor1 |
||
on-chip |
Nordic nRF family TEMP node1 |
||
on-chip |
Nordic nRF quadrature decoder (QDEC) node1 |
||
Serial controller |
on-chip |
||
SPI |
on-chip |
Nordic nRF family SPIM (SPI master with EasyDMA)4 |
|
SRAM |
on-chip |
Generic on-chip SRAM1 |
|
Timer |
on-chip |
ARMv7-M System Tick1 |
|
USB |
on-chip |
Nordic nRF52 USB device controller1 |
|
Watchdog |
on-chip |
Nordic nRF family WDT (Watchdog Timer)1 |
Connections and IOs
Name |
Function |
Usage |
---|---|---|
P0.13 |
GPIO |
Green LED |
P0.14 |
GPIO |
Red LED |
P0.23 |
GPIO |
User Button 1 (BTN1) |
P0.25 |
GPIO |
User Button 2 (BTN2) |
P0.18 |
GPIO |
Reset Button (RST) |
P0.22 |
UART0_RX |
Debug Console |
P0.24 |
UART0_TX |
Debug Console |
Programming and Debugging
The wio_wm1110_dev_kit
board supports the runners and associated west commands listed below.
flash | debug | debugserver | attach | rtt | |
---|---|---|---|---|---|
openocd | ✅ | ✅ | ✅ | ✅ | ✅ |
pyocd | ✅ (default) | ✅ (default) | ✅ | ✅ | ✅ |
Note
The Wio-WM1110 Dev Kit does not include an on-board debug probe. But it can be flashed and debugged by connecting an external SWD debugger to the SWD header.
Flashing
You can build and flash an application in the usual way.
Here is an example for the Blinky application.
# From the root of the zephyr repository
west build -b wio_wm1110_dev_kit samples/basic/blinky
west flash
Debugging
You can debug an application in the usual way.
Here is an example for the Blinky application.
# From the root of the zephyr repository
west build -b wio_wm1110_dev_kit samples/basic/blinky
west debug