SAMA7G54 Curiosity Pro Kit
Overview
The SAMA7G54 Curiosity Pro kit is designed for evaluating and prototyping with the Microchip SAMA7G54 microprocessor (MPU). Based on the SAMA7G54-V/4HB-SL3, the kit provides a feature-rich platform for memory, Ethernet, display, USB, CAN FD, wireless, and debug evaluation.
The SAMA7G54 Curiosity Pro board itself features on-board and expansion Ethernet interfaces, MIPI CSI® and ISC display interfaces, USB host and device connectivity, CAN FD, an M.2 radio-module interface, Raspberry Pi®-compatible GPIO expansion, and two mikroBUS™ connectors.
Hardware
SAMA7G54-V/4HB Microprocessor
128Mb 16-bit low-power mobile DRAM (EM6HF16EBXC)
64 Mb QSPI NOR Flash with EUI-48 (Microchip SST26VF064BEUI-104I/MF)
4 Gb SLC NAND Flash (MX30LF4G28AD-XKI)
2 Kb EEPROM with EUI-48 (Microchip 24AA025E48)
One 4-bit SD card socket
One M.2 radio module with SDIO interface
One device USB Type-C® connector
Two host USB Type-A connectors
One 10/100 RMII on board (Microchip VSC8541XMV)
One 10/100/1000 RGMII SODIMM add-on slot
One MIPI CSI® 34-pin FPC connector
One 30-pin ISC connector
One UART debug connector (FTDI-compatible)
One on-board USB-C®-to-UART converter (Microchip MCP2221)
One JTAG interface
One RGB (Red, Green, Blue) LED
Four push-button switches
Three CAN interfaces
40-pin Raspberry Pi expansion header
2 mikroBUS™ connectors
Power supply unit (Microchip MCP16502TAB-E/S8B)
Power monitoring (Microchip PAC1934)
Daughter card power supply (Microchip MIC23450)
Backup power supply (CR1220 battery holder)
Supported Features
The sama7g54_cpro board supports the hardware features listed below.
- on-chip / on-board
- Feature integrated in the SoC / present on the board.
- 2 / 2
-
Number of instances that are enabled / disabled.
Click on the label to see the first instance of this feature in the board/SoC DTS files. -
vnd,foo -
Compatible string for the Devicetree binding matching the feature.
Click on the link to view the binding documentation.
sama7g54_cpro/sama7g54 target
On-target memory for this board target: 16 MiB of RAM, N/A of Flash.
Type |
Location |
Description |
Compatible |
|---|---|---|---|
CPU |
on-chip |
ARM Cortex-A7 CPU1 |
|
CAN |
on-chip |
Specialization of Bosch m_can CAN FD controller for Atmel SAM6 |
|
Clock control |
on-chip |
Microchip Power Management Controller (PMC)1 |
|
on-chip |
Microchip SCKC1 |
||
on-chip |
Generic fixed-rate clock provider3 |
||
Counter |
on-chip |
Microchip SAM Timer Counter6 |
|
on-chip |
Microchip PIT64B5 |
||
Cryptographic accelerator |
on-chip |
Microchip AES Accelerator G11 |
|
on-chip |
Microchip G1 SHA Controller Driver1 |
||
DMA |
on-chip |
Atmel SAM XDMAC controller3 |
|
Ethernet |
on-chip |
Microchip SAM Ethernet Controller2 |
|
on-chip |
Atmel SAM-family GMAC Ethernet2 |
||
on-chip |
Atmel SAM Family MDIO Driver node2 |
||
GPIO & Headers |
on-chip |
SAM PIO4 GPIO PORT5 |
|
Hardware information |
on-chip |
Microchip G1 hwinfo driver1 |
|
I2C |
on-chip |
||
Input |
on-board |
Group of GPIO-bound input keys1 |
|
Interrupt controller |
on-chip |
ARM Generic Interrupt Controller v21 |
|
LED |
on-board |
Group of GPIO-controlled LEDs1 |
|
Multi-Function Device |
on-chip |
||
MTD |
on-board |
I2C EEPROMs compatible with Atmel’s AT24 family1 |
|
NVMEM |
on-board |
Fixed layout for Non-Volatile memory1 |
|
Pin control |
on-chip |
Microchip SAMA7G5 Pinctrl container node1 |
|
PWM |
on-chip |
Atmel SAM PWM1 |
|
RNG |
on-chip |
Atmel SAM RNG1 |
|
RTC |
on-chip |
Atmel SAM family RTC device1 |
|
SDHC |
on-chip |
Microchip SAM SDMMC SD host controller2 |
|
Serial controller |
on-chip |
||
SPI |
on-chip |
Microchip FLEXCOM SPI1 |
|
SRAM |
on-chip |
Generic on-chip SRAM2 |
|
Timer |
on-chip |
Microchip SAM 64-bit Periodic Interval Timer (PIT64B)1 |
|
USB |
on-chip |
Microchip USB Device High Speed Port (UDPHS) G12 |
Connections and IOs
The SAMA7G54-Curiosity Pro Kit User Guide has detailed information about board connections.
Programming
Prerequisite
Before Zephyr runs on SAMA7G54 Curiosity Pro, at91bootstrap (the second stage bootloader for Microchip MPU) needs to run first. It will initialize the peripherals and memory controllers, download and jump to Zephyr entry point.
Loading the firmware
Using a bootloader compiled with sama7g54_curiosity_prosd_zephyr_defconfig configuration, the binary for Zephyr (zephyr.bin) copied to a SD card can be loaded and run on the SAMA7G54-CPRO board.
References
- SAMA7G54 Product Page:
- SAMA7G54 Curiosity Pro Kit Page: