Nucleo G564RE

Overview

The Nucleo G564RE board is an affordable development platform for the STMicroelectronics STM32G564RE Arm Cortex-M33 microcontroller.

The STM32 Nucleo-64 board provides an affordable and flexible way for users to try out new concepts and build prototypes by choosing from the various combinations of performance and power consumption features provided by the STM32 microcontroller.

More information about the board can be found at the Nucleo G564RE website [1].

Hardware

The STM32G564xx SoC provides the following high-level capabilities used by this board configuration:

  • STM32 microcontroller in an LQFP64 or LQFP48 package

  • 1 user LED

  • Three push-buttons: user, reset, and boot

  • 32.768 kHz crystal oscillator

  • Flexible power-supply options: ST-LINK USB VBUS or external sources

  • External or internal SMPS to generate Vcore logic supply

  • 24 MHz or 48 MHz HSE

  • User USB Device full speed, or USB SNK/UFP full speed

  • Cryptography

  • CAN FD transceiver

  • Board connectors:

    • ARDUINO® Uno V3 expansion connector

    • ST morpho extension pin headers for full access to all STM32 I/Os

    • External SMPS experimentation dedicated connector

    • USB Type-C®, Micro-B, or Mini-B connector for the ST-LINK

    • USB Type-C® user connector

    • MIPI® debug connector

    • CAN FD header

  • On-board ST-LINK (ST-LINK/V2-1, STLINK-V3E, STLINK-V2EC, or STLINK-V3EC) debugger/programmer with USB re-enumeration capability: mass storage, Virtual COM port, and debug port

More information about STM32G564 devices is available at:

Supported Features

The nucleo_g564re board supports the hardware features listed below.

on-chip / on-board
Feature integrated in the SoC / present on the board.
2 / 2
Number of instances that are enabled / disabled.
Click on the label to see the first instance of this feature in the board/SoC DTS files.
vnd,foo
Compatible string for the Devicetree binding matching the feature.
Click on the link to view the binding documentation.

nucleo_g564re/stm32g564xx target

On-target memory for this board target: 112 KiB of RAM, 512 KiB of Flash.

Type

Location

Description

Compatible

CPU

on-chip

ARM Cortex-M33 CPU1

arm,cortex-m33

Clock control

on-chip

STM32G5 RCC.1

st,stm32g5-rcc

on-chip

STM32 HSE Clock1

st,stm32-hse-clock

on-chip

Generic fixed-rate clock provider12

fixed-clock

on-chip

STM32 LSE Clock1

st,stm32-lse-clock

on-chip

STM32G5 PLL11

st,stm32g5-pll-clock

on-chip

STM32 Microcontroller Clock Output (MCO)2

st,stm32-clock-mco

Flash controller

on-chip

STM32G5 flash controller1

st,stm32g5-flash-controller

GPIO & Headers

on-chip

STM32 GPIO Controller8

st,stm32-gpio

on-board

GPIO pins exposed on Arduino Uno (R3) headers1

arduino-header-r3

on-board

GPIO pins exposed on ST Morpho connector1

st-morpho-header

Input

on-board

Group of GPIO-bound input keys1

gpio-keys

Interrupt controller

on-chip

ARMv8-M NVIC (Nested Vectored Interrupt Controller)1

arm,v8m-nvic

on-chip

STM32G0 External Interrupt Controller1

st,stm32g0-exti

LED

on-board

Group of GPIO-controlled LEDs1

gpio-leds

MMU / MPU

on-chip

ARMv8-M MPU (Memory Protection Unit)1

arm,armv8m-mpu

MTD

on-chip

STM32 flash memory1

st,stm32-nv-flash

OTP memory

on-chip

STM32 embedded NVM OTP11

st,stm32-nvm-otp

Pin control

on-chip

STM32 Pin controller1

st,stm32-pinctrl

Reset controller

on-chip

STM32 Reset and Clock Control (RCC) Controller1

st,stm32-rcc-rctl

RTC

on-chip

STM32 RTC1

st,stm32-rtc

Serial controller

on-chip

STM32 USART3

st,stm32-usart

on-chip

STM32 UART3

st,stm32-uart

on-chip

STM32 LPUART1

st,stm32-lpuart

Timer

on-chip

ARMv8-M System Tick1

arm,armv8m-systick

Connections and IOs

Default Zephyr peripheral mapping:

  • Console (LPUART1): PA2 (TX), PA3 (RX)

  • User LED (LD1): PG3

  • User button: PC13

For connector-level details, refer to the board user manual.

System Clock

The default configuration uses a 24 MHz HSE clock and PLL settings (M=3, N=40, P=2) to run the system at 160 MHz.

RTC is enabled and sourced from LSE (32.768 kHz), matching the external LSE crystal present on the board schematic.

Serial Port

The Zephyr console is configured on LPUART1 at 115200 8N1 by default.

Programming and Debugging

The nucleo_g564re board supports the runners and associated west commands listed below.

flash debug debugserver attach
stlink_gdbserver ✅ (default) ✅ ✅
stm32cubeprogrammer ✅ (default)

Nucleo G564RE board includes an STLINK-V3EC embedded debug tool interface.

Applications for the nucleo_g564re board can be built and flashed in the usual way (see Building an Application and Run an Application for more details).

Flashing

The board is configured to be flashed using west STM32CubeProgrammer [4] runner, so its installation is required.

Flashing an application to Nucleo G564RE

Here is an example for the Blinky application.

# From the root of the zephyr repository
west build -b nucleo_g564re samples/basic/blinky
west flash

You will see the LED blinking every second.

Debugging

You can debug an application in the usual way using the ST-LINK GDB Server. Here is an example for the Blinky application.

# From the root of the zephyr repository
west build -b nucleo_g564re samples/basic/blinky
west debug

References