Nucleo H5E5ZJ
Overview
The NUCLEO-H5E5ZJ is an STM32 Nucleo-144 development board based on the STM32H5E5ZJT6 microcontroller. ST identifies the board as MB2129.
The board provides:
An Arm® Cortex®-M33 microcontroller running at up to 250 MHz, with an FPU, an MPU, and Arm TrustZone® support.
4 MiB of internal flash and 1536 KiB of SRAM in an LQFP144 package.
An embedded ST-LINK debug interface and a USART3 virtual COM port.
Three user LEDs: green LD1, red LD2, and blue LD3.
A user push-button and a reset push-button.
Arduino Uno V3 and ST morpho expansion connectors.
A USB high-speed interface with an integrated PHY.
See the NUCLEO-H5E5ZJ product page for board documentation and the STM32H5E5ZJ product page for device documentation. The pin assignments below follow ST’s board configuration, Nucleo BSP, and STM32CubeH5 examples.
Hardware
Supported Features
The nucleo_h5e5zj board supports the hardware features listed below.
- on-chip / on-board
- Feature integrated in the SoC / present on the board.
- 2 / 2
-
Number of instances that are enabled / disabled.
Click on the label to see the first instance of this feature in the board/SoC DTS files. -
vnd,foo -
Compatible string for the Devicetree binding matching the feature.
Click on the link to view the binding documentation.
nucleo_h5e5zj/stm32h5e5xx target
On-target memory for this board target: 256 KiB of RAM, 4 MiB of Flash.
Type |
Location |
Description |
Compatible |
|---|---|---|---|
CPU |
on-chip |
ARM Cortex-M33 CPU1 |
|
ADC |
on-chip |
STM32 ADC2 |
|
CAN |
on-chip |
||
Clock control |
on-chip |
STM32H5 RCC (Reset and Clock controller)1 |
|
on-chip |
STM32 HSE Clock1 |
||
on-chip |
STM32 HSI Clock1 |
||
on-chip |
STM32 HSI48 Clock1 |
||
on-chip |
Generic fixed-rate clock provider2 |
||
on-chip |
STM32 LSE Clock1 |
||
on-chip |
|||
on-chip |
STM32 Microcontroller Clock Output (MCO)2 |
||
Counter |
on-chip |
STM32 counters14 |
|
CRC |
on-chip |
STM32 CRC calculation unit1 |
|
Cryptographic accelerator |
on-chip |
STM32 HASH Processor1 |
|
DAC |
on-chip |
STM32 family DAC1 |
|
Display |
on-chip |
STM32 LCD-TFT display controller1 |
|
on-chip |
STM32 Chrom-ART Accelerator (DMA2D)1 |
||
DMA |
on-chip |
STM32U5 DMA controller2 |
|
Ethernet |
on-chip |
ST STM32 Ethernet MAC1 |
|
on-chip |
Synopsys DesignWare MAC MDIO controller1 |
||
on-chip |
Synopsys DesignWare MAC PTP (Precision Time Protocol) Clock1 |
||
Flash controller |
on-chip |
STM32 Family flash controller1 |
|
GPIO & Headers |
on-chip |
STM32 GPIO Controller11 |
|
on-board |
GPIO pins exposed on Arduino Uno (R3) headers1 |
||
on-board |
GPIO pins exposed on ST Morpho connector1 |
||
I2C |
on-chip |
||
I2S |
on-chip |
STM32H7 I2S controller3 |
|
on-chip |
STM32 SAI Block controller2 |
||
I3C |
on-chip |
STM32H5 I3C controller2 |
|
Input |
on-board |
Group of GPIO-bound input keys1 |
|
Interrupt controller |
on-chip |
ARMv8-M NVIC (Nested Vectored Interrupt Controller)1 |
|
on-chip |
STM32G0 External Interrupt Controller1 |
||
LED |
on-board |
Group of GPIO-controlled LEDs1 |
|
on-board |
Group of PWM-controlled LEDs1 |
||
Memory controller |
on-chip |
STM32 Flexible Memory Controller (FMC)1 |
|
MMU / MPU |
on-chip |
ARMv8-M MPU (Memory Protection Unit)1 |
|
MTD |
on-chip |
STM32 flash memory1 |
|
NVMEM |
on-chip |
Fixed layout for Non-Volatile memory1 |
|
OTP memory |
on-chip |
||
PHY |
on-chip |
This binding is to be used by all the usb transceivers which are built-in with USB IP1 |
|
on-chip |
STM32 USB HS PHY controller (USBPHYC)1 |
||
Pin control |
on-chip |
STM32 pin controller with High-Speed Low-Voltage (HSLV) support1 |
|
Power management |
on-chip |
STM32 power controller1 |
|
on-chip |
STM32 wake-up lines controller1 |
||
on-chip |
STM32H5 I/O cell controller1 |
||
PWM |
on-chip |
STM32 PWM12 |
|
Regulator |
on-chip |
STM32 VREFBUF regulator1 |
|
Reset controller |
on-chip |
STM32 Reset and Clock Control (RCC) Controller1 |
|
RNG |
on-chip |
STM32 Random Number Generator1 |
|
RTC |
on-chip |
STM32 RTC1 |
|
SDHC |
on-chip |
STM32 SDMMC Host Controller2 |
|
Sensors |
on-chip |
STM32 quadrature decoder6 |
|
on-chip |
STM32 Digital Temperature Sensor1 |
||
on-chip |
STM32 family TEMP node for production calibrated sensors with two calibration temperatures1 |
||
on-chip |
STM32 VREF+1 |
||
on-chip |
STM32 VBAT1 |
||
on-chip |
STM32 Vddcore1 |
||
Serial controller |
on-chip |
||
on-chip |
STM32 LPUART1 |
||
on-chip |
|||
SMbus |
on-chip |
STM32 SMBus controller4 |
|
SPI |
on-chip |
||
USB Type-C Port Controller |
on-chip |
STM32 USB Type-C / Power Delivery1 |
|
Timer |
on-chip |
ARMv8-M System Tick1 |
|
on-chip |
|||
on-chip |
STM32U5 LPTIM6 |
||
USB |
on-chip |
STM32 OTGFS controller1 |
|
on-chip |
STM32 OTGHS controller without pinmux1 |
||
Video |
on-chip |
STM32 JPEG HW Codec1 |
|
Watchdog |
on-chip |
STM32 system window watchdog1 |
|
on-chip |
STM32 watchdog1 |
||
xSPI |
on-chip |
STM32 XSPI Controller2 |
|
on-chip |
STM32 XSPI Controller Manager1 |
Default Peripheral Mapping
Interface |
Pins |
Use |
|---|---|---|
USART3 TX / RX |
PD8 / PD9 |
ST-LINK virtual COM port |
UART7 TX / RX |
PB4 / PA8 |
Arduino D1 / D0 |
I2C4 SCL / SDA |
PF5 / PG6 |
Expansion interface |
SPI4 SCK / MISO / MOSI |
PE12 / PE13 / PE14 |
Arduino D13 / D12 / D11 |
FDCAN1 TX / RX |
PD5 / PE0 |
External CAN transceiver |
LD1, green |
PA3, active-high |
|
LD2, red |
PF0, active-low |
|
LD3, blue |
PE5, active-low |
|
User button |
PC13, active-high |
|
TIM2 channel 4 (disabled by default) |
PA3 |
|
ADC1 channels 2 / 6 / 7 / 9 / 3 |
PF11 / PF12 / PA7 / PB0 / PA6 |
Analog inputs |
USB OTG HS |
Dedicated OTG_HS_DM / OTG_HS_DP pins |
|
The console uses USART3 at 115200 baud, 8 data bits, no parity, and one stop bit.
UART7 is also available through the arduino_serial devicetree label.
The green LED is shared by the GPIO and PWM interfaces. Do not use both interfaces for PA3 at the same time. The PWM configuration uses TIM2 channel 4.
SPI4 configures the three data and clock signals. An application must provide the chip-select GPIO required by its SPI device.
FDCAN1 is the default zephyr,canbus controller and requires an external CAN
transceiver.
System Clock
The default configuration follows ST’s clock template: a 48 MHz external crystal feeds PLL1, with M = 12, N = 125, and P = 2. The CPU, AHB, and APB clocks run at 250 MHz. A 32.768 kHz external crystal supplies the RTC.
Memory
The board target exposes the full 4 MiB of internal flash. SRAM1 is the default Zephyr RAM region and provides 256 KiB. SRAM2 through SRAM5 are described by the SoC devicetree and provide the remaining 1280 KiB; they are not included in the default linker RAM region.
Other Interfaces
ST’s board configuration also describes the following Ethernet RMII signals:
Reference clock: PA1
CRS_DV: PD1
RXD0 / RXD1: PC4 / PC5
TX_EN: PA5
TXD0 / TXD1: PB12 / PG12
MDIO / MDC: PA2 / PC1
PHY clock output: PD4
Programming and Debugging
The nucleo_h5e5zj board supports the runners and associated west commands listed below.
| flash | debug | debugserver | attach | |
|---|---|---|---|---|
| stlink_gdbserver | ✅ (default) | ✅ | ✅ | |
| stm32cubeprogrammer | ✅ (default) |
Connect the embedded ST-LINK USB interface to the host. Install STM32CubeProgrammer to use the default flash runner.
Building and Flashing
Build and flash the Hello World application:
# From the root of the zephyr repository
west build -b nucleo_h5e5zj samples/hello_world
west flash
Open the ST-LINK virtual COM port with the console settings above. On Linux,
the port is typically named /dev/ttyACM0. The application prints:
Hello World! nucleo_h5e5zj/stm32h5e5xx
Debugging
The ST-LINK GDB server is configured as the debug runner:
west debug --runner stlink_gdbserver